Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Mike King Today, 3:50 PM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: Troy Gamm Today, 7:09 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: Brian Runau Today, 1:07 PM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Bill Dufour Today, 7:22 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Today, 6:05 PM

LLAMBRICH Intergrated arbor and chuck
Thread Starter: Patty Hann
Opinions, please on integrated arbor and chuck for a DP. Am looking at the LLAMBRICH Keyless chucks ... integrated 2MT shank/arbor 1/32" to 3/8" (part# JK10-MT2) 1/32" to 1/2" (JK13-MT2) Thanks
Last Post By: Patty Hann Today, 1:45 PM

Bob Andre

There is no available content written by Bob Andre

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Swiss Army ... tool

They make a variety of "tool combinations" already so doing something like this for folks who don't want/don't need/can't have a blade fit into
Jim Becker Today, 7:42 PM

Shop Project: Finally flattening my main bench top

Thanks, Michael. It's a satisfying completion of the project.

-----

I added something to this bench recently that I forgot to
Jim Becker Today, 7:32 PM

delta DJ 15 jointer upgrade

Some older jointers were direct drive. What rpm did the turn? Some direct drive bandsaws had odd low speed motors like 900 rpm.
BilL D
Bill Dufour Today, 7:31 PM

delta DJ 15 jointer upgrade

Was this the factory motor? I would guess around 3,500 for the cutter head so a cheaper high speed motor would be used from the factory. A high speed
Bill Dufour Today, 7:29 PM

SCM T130 bearing change

Get a hardened nut that will slip over the shaft. Grind away most of one end to leave two little ears to fit the slots. Use a socket to turn the nut.
Bill Dufour Today, 7:22 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Bob Andre

Recent Polls

Recent Forum Posts

Recent Blog Posts