• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Jerome Stanek

    Glowforge release

    Thread Starter: Jerome Stanek

    I was wondering if Glowforge has sent out any units yet. I thought they were supposed to release the middle of December.

    Last Post By: Bert Kemp Today, 11:17 PM Go to last post
    Ryan Pappas

    Hammer slider vs. Minimax

    Thread Starter: Ryan Pappas

    I have decided to sell my sawstop and get a sliding table saw. I have narrowed it down to hammer k3 79x48 and minimax. I have the SC2 and the SC4 in mind for minimax. Also adding in the SC3 to the mix. I mainly make end grain cutting boards so not sure if a full 8ft is necessary for me but I know...

    Last Post By: Peter Kelly Today, 10:22 PM Go to last post
    John C Cox

    Show me your chisel racks

    Thread Starter: John C Cox

    Hey guys, I need to make a bench top or wall mounted chisel rack and need some ideas... What is your favorite one you have made? Pix please. :D :D Also - do you do anything differently for socket chisels vs tang chisels. I would hate to find the beautiful socket chisel irons all...

    Last Post By: Nicholas Lawrence Today, 10:30 AM Go to last post
    Ray Newman

    Waterstones

    Thread Starter: Ray Newman

    Colleagues: need some recommendations as to a water stone set. Am tired of the Tormek required pre soaking time before use. As a result, I put off sharpening or touching up the edge until it is really dull. Last time I was at the local tool emporium, clerk raved about the Shapton glass backed...

    Last Post By: Chet R Parks Today, 12:14 PM Go to last post
    Brandon SPEAKS

    one premium plane

    Thread Starter: Brandon SPEAKS

    So this is mostly hypothetical. If you were to have a plane collection build on decent user vintage planes but could buy one premium LN or LV what would it be? A no 4 because of the advantages of perfectly tuned smoother plane? A specialty like a shooting plane and tracks for a shooting...

    Last Post By: Jim Koepke Today, 9:31 PM Go to last post
    Rob Wolfbrandt

    need advice on track saw related purchases for building built-ins at home

    Thread Starter: Rob Wolfbrandt

    Hi Everyone, I've been reading this forum the past two days collecting as much information as I can about track saws, accessories, and the Festool MFT/3 table. There's so much knowledge and experience here that I thought it a good idea to request some opinions on what I'm thinking about doing. ...

    Last Post By: Rob Wolfbrandt Today, 8:56 PM Go to last post
  • Jason Hanko

    There is no available content written by Jason Hanko
  • Recent Polls

    Which Coping Sled is the Best (Votes: 44)

    1. Woodpeckers Coping Sled (Votes: 16)

    2. Infinity Professional Coping Sled (Votes: 16)

    3. Neither - Who needs a sled anyway? (Votes: 10)

    4. Both - Why buy only one when you can have two at twice the price? (Votes: 2)

  • Recent Forum Posts

    Filip Winiewicz

    Carbide tool tips quality

    Guys, thank you for your replies. How about cnc carbide cutters for steel? I've found cheap Mitsubishi carbide cutters that should have high quality.

    Filip Winiewicz Today, 11:28 PM Go to last post
    Bert Kemp

    corel problem smRT fill

    I'll try it again Kev, I did the idea Tony gave me and that worked , but I'll load the orginal again remove nodes Like Tony said, I'll take out those

    Bert Kemp Today, 11:23 PM Go to last post
    Bert Kemp

    Problem engraving.

    It really would help if we knew which machine , size. power and model

    Bert Kemp Today, 11:20 PM Go to last post
    Kevin Jenness

    Marking on dark wood?

    For a fine visible line, apply tape, slice the line with a knife and remove the tape on the waste side. I use this all the time for scribeing.

    Kevin Jenness Today, 11:17 PM Go to last post
    Bert Kemp

    Glowforge release

    Im sorry Bill where was it that he said that? I went back looking couldn't find that post. What number was it ?

    Bert Kemp Today, 11:17 PM Go to last post
  • Recent Blog Posts