Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Jim Koepke Yesterday, 3:25 PM

Milling machine as a mortiser
Thread Starter: andrew whicker
Hi all, I don't look often, but when I do it seems there are absolutely no used mortising machines out there. Something I've always wanted (someday) was a knee mill. There's a place near me that has had a Cincinnati Contour Master for sale forever (years and years). They re build these...
Last Post By: Bruce Page Today, 1:20 PM

Dumb answers to dumb questions
Thread Starter: Zachary Hoyt
I used to feel frustrated when I would have listed something for sale on Craigslist or Facebook and included the town where I lived, and instead of looking it up on their devices people would write to me to ask "where is Orwell" (where I used to live) or now "where is Piercefield?". I finally...
Last Post By: Patty Hann Yesterday, 11:12 PM

Are they building standalone car washes like crazy in your area too?
Thread Starter: Brian Elfert
They are going crazy building standalone car washes in my area. I know of at least three currently under construction nearby, and a few others that recently opened. Car washes are going up all over the Minneapolis metro area. There will easily be three times as many standalone car washes once...
Last Post By: Cameron Wood Yesterday, 2:37 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Today, 11:58 AM

Adhesive with a long open time
Thread Starter: Tim Andrews
Greetings All, I’ve done a search here, but all the threads I have seen are old. I would like a recommendation for an adhesive with a long open time for complicated glue ups, minimum 30 minutes,. I typically use Titebond 3 but would like more time for some projects. Sometimes it’s possible to do...
Last Post By: Wes Grass Yesterday, 11:14 PM

Curtis O. Seebeck

There is no available content written by Curtis O. Seebeck

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Milling machine as a mortiser

My Logan mill uses R8 collets. That, and every Bridgeport I have ever run (dozens of them) that used R8 collets required a tap on the drawbar to break
Bruce Page Today, 1:20 PM

Anyone with temperature controller experience?

Thanks, I'll have a look and see if they have a solution.
Doug Garson Today, 1:09 PM

Anyone with temperature controller experience?

Not sure an air to air heat exchanger would be applicable in my case. Air to air heat exchangers recover heat from exhaust air to heat incoming air
Doug Garson Today, 1:05 PM

Milling machine as a mortiser

AFAIK you have to make your own nut cage etc to make it a self ejecting drawbar. R8 tends to fall out on its own. Most other milling taper sare much
Bill Dufour Today, 1:01 PM

Bandsaw Blade Gave Good Service

I'm one who has never had a good experience with TimberWolf blades. I never found them to be particularly sharp, which then required more feed pressure,
Edward Weber Today, 12:05 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Curtis O. Seebeck

Recent Polls

Recent Forum Posts

Recent Blog Posts