Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Jim Allen Today, 5:25 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 11:20 PM

Residential fence rules
Thread Starter: Stan Calow
I am looking for what people in other jurisdictions have dealt with. I have always understood that, in my city, fences between homes were the responsibility of the homeowner who first puts it up. And the rule was "good side out" and 6" off the property line. But after a discussion with a...
Last Post By: Pat Germain Today, 4:57 PM

California bans gas lawn mowers and leaf blowers after 2024
Thread Starter: Bill Dufour
Saw a sign at hoe despot and looked it up. California has banned the sale of gas lawnmowers and leaf blowers after 2024. If yours is getting tired better buy a new one in a few months. I assume they will be gone from stores by Fall. It will probably take ten to twenty years until this ban goes...
Last Post By: Edward Weber Today, 5:47 PM

Harvey COMPASS RG-1/RG-2 Universal Roller Guides Question
Thread Starter: James Cheever
All - Has anyone seen or used the Harvey COMPASS RG-1/RG-2 Universal roller guides. They look solid and would be a pretty useful addition to my shop, but the price seems way too high. I'd love to hear any feedback. Thanks.
Last Post By: Lloyd McKinlay Yesterday, 9:46 PM

Grease..... and not the movie....
Thread Starter: Karl Card
I have a baldor 7.5HP BALDOR 3450RPM 213T TEFC 1PH MOTOR L3709Ton my table saw. What type of grease should I look for to put grease in the grease or zirk fitting?
Last Post By: Roger Feeley Today, 3:24 PM

Jonathan Baker

There is no available content written by Jonathan Baker

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

California bans gas lawn mowers and leaf blowers after 2024

It's not just the cost increase or environmental benefits, they simply do not make viable battery powered alternatives to many SORE powered machines that
Edward Weber Today, 5:47 PM

Outdoor Oil

I missed summer #3. Now reporting in summer #4. Heartwood cherry garden chairs with General Finishes outdoor oil, with northern exposure - sun perhaps
Mark Rainey Today, 5:45 PM

Stumpy Nubs Video - Do you flat or hollow grind?

I generally end up with flat ground chisels and plane blades because I'm a hand sharpener. For years, I messed around with all sorts of sharpening systems
Randy Heinemann Today, 5:37 PM

Good source if you want to try Japanese planes

Sawdust and guts! Gives "Chainsaw Massacre a whole new meaning.
Kevin Jenness Today, 5:31 PM

HF (Bauer) carbide router bits?

I've bought items from HF when I know I'm not going to use them a lot. For example, I bought a 24 ga pin nailer for somewhere around $10-$15 and, because
Randy Heinemann Today, 5:29 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Jonathan Baker

Recent Polls

Recent Forum Posts

Recent Blog Posts