• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Ken Fitzgerald

    Shop lighting......

    Thread Starter: Ken Fitzgerald

    Here's an article that answers a lot of shop lighting questions that are so often asked here. http://www.sawmillcreek.org/content.php?146-Lighting-the-Small-Workshop-by-Jack-Lindsey

    Last Post By: Mike OMelia Today, 3:16 PM Go to last post
    Erich Weidner

    Squaring Up Really Long Boards... Tips?

    Thread Starter: Erich Weidner

    I have a few dozen long boards I need to glue up into large panels. (11' to 16' for each section). They will be about 32" wide. I'm gluing up from 1 x 6 S4S stock. (So nominally 3/4" x 5-1/2"). They of course all have some bow, cup, or twist. I don't care at all about the look of one flat face...

    Last Post By: Erich Weidner Yesterday, 11:41 PM Go to last post
    steven c newman

    A new Desk for me

    Thread Starter: steven c newman

    "old" one is cramped, small drawers....not enough room for the computer I am using...so. Came up with a rough "Plan".. Picked up about 40bf of Ash....($20.....) Then drew up a better Plan... More as a guide, than anything carved in stone....(already a few design changes have been made..)...

    Last Post By: steven c newman Yesterday, 9:55 PM Go to last post
    Ole Anderson

    Craftsman at Lowe's and Ace

    Thread Starter: Ole Anderson

    Anybody else get the tinglies now when walking into Lowe's and seeing row on top of row of red Craftsman tools, chests and equipment? Not that I am such a fan of their stuff, just that it brings back good memories of trolling through the Sears tool department years ago. Even my local Ace carries...

    Last Post By: Ronald Blue Yesterday, 7:06 PM Go to last post
    lowell holmes

    Tool rust prevention

    Thread Starter: lowell holmes

    In the current issue of This Old House Magazine, a reader ask Tom Silva how he prevents rust on his tools. I live in Galveston County Texas, so I Know a bit about rust. I coat my tools with Johnson's Floor Wax. They do not rust. I thought some new woodworkers might be interested.

    Last Post By: Jacob Mac Yesterday, 9:11 PM Go to last post
    Alan Lightstone

    Soundproofing for workshop entry wall

    Thread Starter: Alan Lightstone

    Finally getting a contractor to put the walls up in my workshop. I've been looking at a variety of techniques for soundproofing the walls (it's an interior wall to my garage, the exterior walls are cinderblock and aren't being done now. There will be a double outside rated entry door from the...

    Last Post By: Frank Pratt Today, 2:52 AM Go to last post
  • Lee Schierer

    There is no available content written by Lee Schierer
  • Recent Polls

  • Recent Forum Posts

    ken hatch

    Sharpening Bench

    Because of Monsoon and the heat most of my shop time today will be spent sharpening whatever needs it and maybe a few that don't, that got me to thinking

    ken hatch Today, 3:30 PM Go to last post
    Mark Blatter

    tis a different age

    We had a bad hail storm last summer that took out most of the roofs where I live. Pretty unusual as Utah just doesn't get the kind of storms that the

    Mark Blatter Today, 3:25 PM Go to last post
    Mike OMelia

    Shop lighting......

    So much to consider. I used this thread several years ago to light my garage shop with florescent lighting. Worked great. Trying to find a calculator

    Mike OMelia Today, 3:16 PM Go to last post
    Jerome Stanek

    Today In History July 20th

    I was in AIT at Ft McClellan we were aloud to watch the landing in the day room

    Jerome Stanek Today, 3:08 PM Go to last post
    marlin adams

    Cutech Jointer

    Well got my cutech 6" jointer and my wen 13" planer up on movable benches and ran some scrap 2x4s thru the jointer after setup which was a breeze

    marlin adams Today, 3:02 PM Go to last post
  • Recent Blog Posts