Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Rocks in their heads
Thread Starter: Edward Weber
https://www.ktnv.com/news/park-rangers-looking-for-two-vandalism-suspects-at-lake-mead-national-recreation-area What the ____ is wrong with some people?
Last Post By: Doug Garson Yesterday, 4:45 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 6:54 PM

Glue Chairs
Thread Starter: Dave Fritz
We’re gluing old chairs that have come a little loose. Any tips on how to get Titebond in a small crack? Will thinning make it useless? Thank you.
Last Post By: David Storer Yesterday, 4:14 PM

Grease..... and not the movie....
Thread Starter: Karl Card
I have a baldor 7.5HP BALDOR 3450RPM 213T TEFC 1PH MOTOR L3709Ton my table saw. What type of grease should I look for to put grease in the grease or zirk fitting?
Last Post By: John C Cox Yesterday, 4:38 PM

Stainless steel figure 8 hardware
Thread Starter: Brian Runau
Looking for ideas to attach a table top to the base on an outdoor dining table. Thought to use stainless steel figure 8's, but I can only find ones that are @ 7/17" overall length which is way to small. Normal steel units are 1.3" long. Table has a 5' wide frame with a 35" marble insert and a 3"...
Last Post By: STUART Robertson Yesterday, 3:02 PM

Beaded faceframe tooling question (grinding shaper cutter)
Thread Starter: Shannon Brantley
I've got a cabinet shop, been in the business for almost 10 years and suddenly I've got 2 potential jobs that want beaded face frames. One has 94 doors and drawer fronts. So I bought (luckily found one) a new, discontinued, Kreg PRS1200 system. It comes with router bits for the bead. I'd like...
Last Post By: STUART Robertson Yesterday, 8:27 PM

Luck Leventopoulos

There is no available content written by Luck Leventopoulos

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Timesaver 137-1HD / 36" wide belt sander _ one head

Great older time savers I have a similar one and it served me very very well as the others have said you got a check the service of the rollers and also
lou sansone Today, 3:53 AM

Adhesive with a long open time

I use epoxy often. Totalboat with med or slow hardener or System 3 T-88.

Almost every project I build uses epoxy in part of the glue-up.
Michael Burnside Today, 12:58 AM

Monarch Unipoint Saw

Any relation to the safety speed cut panel saw?
BillD
Bill Dufour Today, 12:53 AM

Vietnam veterans....

Yep, I get my hearing aids through the VA. For years, I never applied to the VA because I felt there were people who deserved it a lot more than me.
Mike Henderson Today, 12:24 AM

Adhesive with a long open time

i use urea resin for such things. Unibond 800, and i thicken and tint it to get the consistency and color i want. very long open time, but requires
David Zaret Yesterday, 11:23 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Luck Leventopoulos

Recent Polls

Recent Forum Posts

Recent Blog Posts