• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Michael Arruda

    Home Depot return policy change without notification

    Thread Starter: Michael Arruda

    Hello all, I had some small items left over from various things I've done around the house recently and decided to gather them up to take back to Home Depot. These items were purchased at various times over the past couple weeks and I of course misplaced my receipts. Meaning they got washed,...

    Last Post By: william watts Today, 1:05 AM Go to last post
    John McGovern

    Table Saw Questions

    Thread Starter: John McGovern

    Hi All, I've been lurking in the weeds for some time and have found this venue to be the most knowledgeable, helpful, and courteous forum on the block. And, I know this question has been asked and answered so many times, but I hope you all have the patience for one more dip to the well to answer...

    Last Post By: Thomas McCurnin Yesterday, 7:24 PM Go to last post
    Paul F Franklin

    New Lee Valley Web Site

    Thread Starter: Paul F Franklin

    Seems the roll out of the new site is not going completely smoothly. Have been trying to place an order all morning and the site just spins when I try to checkout. Tried a few different browsers too. Guess I may have to call :eek: New site design seems nice and clean though but it will take...

    Last Post By: Jim Koepke Yesterday, 10:30 AM Go to last post
    Carl Beckett

    Dust collection barrel

    Thread Starter: Carl Beckett

    What is everyone using for a dust collection barrel? I have a heavy duty plastic trash can I put a gasket on. But it 'implodes' at times. Before I go messing with reinforcement, maybe I should just ditch it all together for something more suitable (ideally cheap and readily available locally). ...

    Last Post By: Tom Bender Yesterday, 5:15 PM Go to last post
    Carl Beckett

    Tablesaw dust collection hood

    Thread Starter: Carl Beckett

    Well, after a weekend working with black walnut I have GOT to improve my tablesaw dust collection. Which means time to put the blade guard/collection hood at the top of the project list. The support arm will be home made. The guard/hood can be either home made or purchased, but since I want to...

    Last Post By: Tom Bender Yesterday, 7:23 PM Go to last post
    Tom Trees

    Suitable relay for three wire control on a VFD

    Thread Starter: Tom Trees

    Hello folks I have been walking through the steps with another forum member on setting up a VFD for his saw. Unfortunately the VFD does not have a relay OR COMMON for three wire control/push button station. Can any of you guys point me in the right direction to find a suitable relay for him? ...

    Last Post By: David L Morse Today, 5:01 AM Go to last post
  • Jim Andrew

    There is no available content written by Jim Andrew
  • Recent Polls

  • Recent Forum Posts

    Jim Becker

    Jointer Safety

    The ground surface is particularly helpful when face jointing wider stock because as the material actually gets "flat", the effect with a flat,

    Jim Becker Today, 8:55 AM Go to last post
    Phil Mueller

    Keeping Tools Rust Free - Wax or Oil?

    I’m in Michigan with high humidity in the summer. Like Jim, I run a dehumidifier all summer in the shop, and made an oil pot. Everything gets

    Phil Mueller Today, 8:55 AM Go to last post
    Phil Mueller

    Sharpening Help?

    Nice job, Rob. I didn’t jump in to the sharpening discussion, because I have no experience...but wanted to say the spoon looks fantastic. I’d

    Phil Mueller Today, 8:49 AM Go to last post
    Jim Becker

    DC Duct Length Below Cyclone

    Just to add to your confidence, I helped a local friend install her Oneida cyclone in the upstairs of her shop building. The barrel is on the floor in

    Jim Becker Today, 8:43 AM Go to last post
    Bob Falk

    Good quality mobility bases?

    +1 I've had a few commercial mobile bases for various tools and sold them all. While all were solidly constructed, the lack of swivel wheels (especially

    Bob Falk Today, 8:43 AM Go to last post
  • Recent Blog Posts