Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Mike King Today, 3:50 PM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: Troy Gamm Today, 7:09 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: Brian Runau Today, 1:07 PM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Bill Dufour Today, 7:22 PM

LLAMBRICH Intergrated arbor and chuck
Thread Starter: Patty Hann
Opinions, please on integrated arbor and chuck for a DP. Am looking at the LLAMBRICH Keyless chucks ... integrated 2MT shank/arbor 1/32" to 3/8" (part# JK10-MT2) 1/32" to 1/2" (JK13-MT2) Thanks
Last Post By: Patty Hann Today, 1:45 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Today, 6:05 PM

barry holman

There is no available content written by barry holman

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

2 items from a Road Trip

This one was in use, today..

Fine Tuning rebates...so that the rails will go on better...without binding..
steven c newman Today, 8:38 PM

Gable Vent

Remember that old Sears RAS you couldn't wait to get rid of.. Louver shops had a pair set up for right and left cuts. As for fans lasting, did they get
Bruce Wrenn Today, 8:32 PM

blade insert for delta/rockwell 12/14

Thanks. Many good ideas here.
Karl Card Today, 8:28 PM

Property tax assessment question

Here local county only sends a bill if it's over five bucks. I own three multiyear licensed trailers. Tax is collected at renewal, but because there
Bruce Wrenn Today, 8:25 PM

Swiss Army ... tool

If it goes past the TSA, I’m in. It could be my travel knife. Of course there will be plenty of pointy things that could be a weapon. For that matter,
Roger Feeley Today, 8:09 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

barry holman

Recent Polls

Recent Forum Posts

Recent Blog Posts