Sawmill Creek Woodworking Community - Powered by vBulletin
  • Register
  • Help
  • What's New?
  • Forum
  • Articles
    • The Sawmill Creek Press
  • Blogs
  • Donate
  • Sponsors
  • Friends of the Creek
  • Advanced Search
  • Home
  • Home
  • The Sawmill Creek Press

  1. If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

  • Sections

    • Sawmill Creek News
    • Workshops
    • Woodturning
    • Social Woodworking
    • Tools
      • Lathes and Accessories
      • Table Saws and Accessories
    • Jigs and Fixtures
    • Cabinetry

  • Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Dave Anderson NH

    Time for some levity

    Thread Starter: Dave Anderson NH

    With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.

    Last Post By: Dave Anderson NH Yesterday, 4:08 PM Go to last post
    Dale Osowski

    Krenov Style Apron Plane

    Thread Starter: Dale Osowski

    Attention to my woodworking friends! I have a fair amount of Gaboon Ebony cutoffs I've collected over the years and I'm looking to put them to good use. I'm thinking about making a number of small Krenov style apron / block planes that would be available for sale. They would be made of Gaboon...

    Last Post By: Dale Osowski Today, 10:38 AM Go to last post
    Jonathan Jung

    Cost effectiveness of a slider vs. tracksaw & tablesaw

    Thread Starter: Jonathan Jung

    I thought about posting this to the business section, because I'd really like input from professionals who use their shop as a business. For those of you who make $ or even a living making furniture or cabinets, how long does it take for a sliding table saw to pay for itself compared to a track saw...

    Last Post By: Ronald Blue Today, 9:20 AM Go to last post
    Bill Brammer

    Solid Walnut bookshelf dados - is glue enough?

    Thread Starter: Bill Brammer

    Building 6 ft high, 28 in wide, 12 inch deep solid 3/4 inch walnut bookshelf , no adjustable shelves. I have dados for all shelves. The sides are a little bowed, requiring some pressure with clamps to pull them together with the dados. Not a ton, but some. I'm trying to decide if I need to add...

    Last Post By: johnny means Yesterday, 7:11 PM Go to last post
    Gregg Feldstone

    Lift lock and roll

    Thread Starter: Gregg Feldstone

    I wish I had bought the lift lock and roll mobility device which apparently is not made anymore. Does anyone know where I could get one or have one to sell? I need it for my PM 3520 B

    Last Post By: Roger Chandler Today, 10:30 AM Go to last post
    Bryan Cleveland

    Return Air Baffle for CV1800

    Thread Starter: Bryan Cleveland

    I’ve been designing a closet for my CV1800 for a few months trying to find a way to make it fit in my little garage and I think I have finally cracked it. My only concern is with the return air baffle I designed. Garage is air conditioned so return air is a must. I’ve read so many posts about...

    Last Post By: Frank Pratt Yesterday, 11:57 AM Go to last post

  • Jack McKee

    Woodshop for Kids.....is not just woodworking 

    by
    Jack McKee
    • View Profile
    • View Forum Posts
    • View Blog Entries
    • View Articles
    Published on 01-31-2015 9:16 PM

    Woodworkingfor Kids.....isnot just woodworking


    Kids need Hands On activities. ...
    Read More Read More 4 Comments

    8th Graders Construct Builder Boards for the Women's Care Shelter 

    by
    Jack McKee
    • View Profile
    • View Forum Posts
    • View Blog Entries
    • View Articles
    Published on 02-22-2011 12:31 PM     Number of Views: 41258 
    Article Preview


    Woodworking, teamwork, and community service - all in one project.
    ...
    Read More Read More 9 Comments

    How to Build the Magnetic Marble Roll 

    by
    Jack McKee
    • View Profile
    • View Forum Posts
    • View Blog Entries
    • View Articles
    Published on 01-19-2011 12:25 AM     Number of Views: 31103 
    Article Preview

    Woodworking for Kids: Building a Magnetic Marble Roll. Jack discusses the design and assembly of an intriguing toy for kids. ...
    Read More Read More 9 Comments

  • Recent Polls

  • Recent Forum Posts

    Dale Osowski

    Krenov Style Apron Planes

    Even though I have a Tormek T8 I'm going to give the Scary Sharp System a try. All the blades in the photo have already been flattened & sharpened

    Dale Osowski Today, 10:39 AM Go to last post
    Dale Osowski

    Krenov Style Apron Plane

    Even though I have a Tormek T8 I'm going to give the Scary Sharp System a try. All the blades in the photo have already been flattened & sharpened

    Dale Osowski Today, 10:38 AM Go to last post
    Roger Chandler

    Update to parts search

    Good to hear, Ted. You have the G0800, correct? What happened to make your lathe have issues? Thunderstorms, power surge, big catch?

    Roger Chandler Today, 10:35 AM Go to last post
    Roger Chandler

    Lift lock and roll

    Back home now, and hope at least to get started in the next few days. Got some major lawn work to do though, rains and high temps while away have gotten

    Roger Chandler Today, 10:30 AM Go to last post
    Pat Germain

    Polyaspartic Garage Floor Coating?

    Thank you.

    Pat Germain Today, 10:30 AM Go to last post

  • Recent Blog Posts

  • Contact Us
  • Sawmill Creek
  • Archive
  • Terms of Service
  • Top
All times are GMT -4. The time now is 10:40 AM.
Powered by vBulletin® Version 4.2.5
Copyright © 2022 vBulletin Solutions Inc. All rights reserved.