Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Kevin Jenness Today, 12:14 PM

Spindle gouge bevel angle?
Thread Starter: John Kananis
I have a 1/2" sorby detail gouge that I have ground at 40° (also removed the heel) and it works ok now that I moved away from the jigs and started sharpening by hand... but it's still just an ok tool. I now have a d-way detail spindle gouge (1/2") on the way and was thinking about trying a 25°...
Last Post By: John Kananis Yesterday, 2:16 PM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: John Kananis Today, 10:24 AM

Need ideas on waterproof board to cover water damaged base of outside doors
Thread Starter: Randall J Cox
I have two exterior doors, one to the back of my house and one to my tool shed. Both are showing the effects of winter water splashing up on them at the base. The door to my shed is really bad. I don't want to replace the doors but would like to put a board over the base, like a kickplate to...
Last Post By: Stan Calow Today, 9:20 AM

Hot water sulfur smell solutions
Thread Starter: Ron Citerone
My cottage is on well water. Several years ago we started with the dreaded sulfur smell, hot water only. I had a plumber replace the anode. Smell came back eventually. I found the model of the anode he installed and see that is just aluminum. Seems like the one I need is aluminum/zinc? Has...
Last Post By: Bill Howatt Today, 9:43 AM

Vectric Software V12 Now Available
Thread Starter: Michael Burnside
I was talking with friend over the weekend and they were unaware that V12 has been released. So, I figured I would post here in case someone wasn't aware of this news. In general the upgrades look good overall. I personally upgraded my version of Vcarve Pro.
Last Post By: Grant Wilkinson Today, 12:08 PM

Clint deal

There is no available content written by Clint deal

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Charcuterie Board Handle

Kenin,

Those boards look great. What finish did you put on the make that maple POP! Like others mentioned, I would put feet under those boards.
Mike Congiusti Today, 1:49 PM

SCM T130 bearing change

Jim, I will try there. The T130 does not have a serial # tag on it but will try there with out the #s and see. Thanks
Tom Yaegle Today, 1:47 PM

Dewalt DW735 Planer for short hardwood boards?

I think quality of the surface with new HSS non spiral blades and a carbide spiral cutterhead are about the same. But those HSS blades tend to degrade
Mark Wedel Today, 1:39 PM

Systainers?

Fortunately I have a big hayloft to store the empty systainers because I can't bear to throw them away.
roger wiegand Today, 1:38 PM

Which 3M Versaflo? Or?

It looks like more stuff is included with the HIK than the ECK according to the two 3M links below.
https://www.3m.com/3M/en_US/p/dc/v100559007/
Steve Mathews Today, 1:18 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Clint deal

Recent Polls

Recent Forum Posts

Recent Blog Posts