Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Mike King Yesterday, 3:50 PM

Spindle gouge bevel angle?
Thread Starter: John Kananis
I have a 1/2" sorby detail gouge that I have ground at 40° (also removed the heel) and it works ok now that I moved away from the jigs and started sharpening by hand... but it's still just an ok tool. I now have a d-way detail spindle gouge (1/2") on the way and was thinking about trying a 25°...
Last Post By: Don Frank Today, 8:57 AM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: Troy Gamm Yesterday, 7:09 PM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Warren Lake Yesterday, 8:56 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: Brian Runau Yesterday, 1:07 PM

Freud hand held router FT2200VCE bit is moving
Thread Starter: Brian Runau
I use this to do hand work and it has worked fine over the years. I have it set right now to do some template work and it is/was set for 5/16" depth. Bit seems to be tight in the collect and the locking lever is/was tight. This morning as I was routing 16 spots on night stand legs to let in a...
Last Post By: Jim McLeod Today, 5:45 AM

Geoff Hanha

There is no available content written by Geoff Hanha

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Glue Chairs

Thinning PVA glue with water works really well. I do it all of the time for various reasons. Sometimes, to get it through the needle of a syringe.
Jimmy Harris Today, 10:19 AM

What paint for a new exterior fiberglass door?

I agree with Jason...go to a real paint store and get their recommendation for your application and area. I personally use SW and for my front door, Emerald
Jim Becker Today, 9:52 AM

Swiss Army ... tool

Same at my school. What was not allowed was switchblades or sticking knives in desks.

Ne neither.
Alan Rutherford Today, 9:50 AM

If you like shop built tools, this video is pretty enjoyable...

If you like shop built tools, this video is pretty enjoyable...even though it's nearly an hour and a half. Marius Hornberger decided to make an OSS/OBS
Jim Becker Today, 9:50 AM

Shop Project: Finally flattening my main bench top

Ken, my flattening system is from TrueTrac, but yes, there are a number of them commercially available as well as lots of "shop built" solutions.
Jim Becker Today, 9:36 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Geoff Hanha

Recent Polls

Recent Forum Posts

Recent Blog Posts