Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Patty Hann Yesterday, 9:14 AM

Are they building standalone car washes like crazy in your area too?
Thread Starter: Brian Elfert
They are going crazy building standalone car washes in my area. I know of at least three currently under construction nearby, and a few others that recently opened. Car washes are going up all over the Minneapolis metro area. There will easily be three times as many standalone car washes once...
Last Post By: Warren Lake Yesterday, 9:08 AM

Spindle gouge bevel angle?
Thread Starter: John Kananis
I have a 1/2" sorby detail gouge that I have ground at 40° (also removed the heel) and it works ok now that I moved away from the jigs and started sharpening by hand... but it's still just an ok tool. I now have a d-way detail spindle gouge (1/2") on the way and was thinking about trying a 25°...
Last Post By: John Kananis Yesterday, 2:16 PM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: Troy Gamm Yesterday, 2:51 PM

Need ideas on waterproof board to cover water damaged base of outside doors
Thread Starter: Randall J Cox
I have two exterior doors, one to the back of my house and one to my tool shed. Both are showing the effects of winter water splashing up on them at the base. The door to my shed is really bad. I don't want to replace the doors but would like to put a board over the base, like a kickplate to...
Last Post By: Rich Engelhardt Yesterday, 12:29 PM

Vectric Software V12 Now Available
Thread Starter: Michael Burnside
I was talking with friend over the weekend and they were unaware that V12 has been released. So, I figured I would post here in case someone wasn't aware of this news. In general the upgrades look good overall. I personally upgraded my version of Vcarve Pro.
Last Post By: Jim Becker Today, 8:31 AM

John S Howland

There is no available content written by John S Howland

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Vectric Software V12 Now Available

Be sure you post about that command change in the Vectric forum so it can be addressed by Vectric staff.
Jim Becker Today, 8:31 AM

SCM T130 bearing change

Tom, have you tried Parts Pronto which is part of the SCM website? You have to register, but that's the parts and manuals part of the company.
Jim Becker Today, 8:30 AM

SCM T130 bearing change

You can't leave off the "SCM" from the search...it's conceivable that many companies might have "things they make" that use the same
Jim Becker Today, 8:28 AM

SCM T130 bearing change

Jerry, I have not found a good parts break down with google?

Jared, I read that but have not found any good info, just that they changed
Tom Yaegle Today, 8:24 AM

landscaping is my other hobby, record for me, 25 yards of mulch

I am surrounded by yards full of dandelions, but refuse to give in. Thick lawn is key, built it up over a few years and got to the point it is easy to
Brian Runau Today, 8:05 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

John S Howland

Recent Polls

Recent Forum Posts

Recent Blog Posts