Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Mike King Yesterday, 3:50 PM

Spindle gouge bevel angle?
Thread Starter: John Kananis
I have a 1/2" sorby detail gouge that I have ground at 40° (also removed the heel) and it works ok now that I moved away from the jigs and started sharpening by hand... but it's still just an ok tool. I now have a d-way detail spindle gouge (1/2") on the way and was thinking about trying a 25°...
Last Post By: Don Frank Today, 8:57 AM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: John Kananis Today, 10:40 AM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Brian Holcombe Today, 3:02 PM

Powermatic Model 80 20" Bandsaw - Yes or No?
Thread Starter: Brent Ring
All, I have been in the market for a bigger bandsaw. Starting to build some rocking chairs a la Hal Taylor, and my PM 141 does not have enough clearance to make a few of the cuts needed. A Powermatic 80 20" had come up in my area, for a little under $1k. Owner states it runs smooth, cuts well....
Last Post By: Mickey Plunkett Today, 11:47 AM

Swiss Army ... tool
Thread Starter: Edward Weber
https://www.cnn.com/2024/05/07/business/swiss-army-knife-blade-scli-intl/index.html While I understand the decision, I can't help think that, I carry a pocket knife, with a blade only and use it for so many tasks. I think I would be fumbling through the selection of tools trying to find a...
Last Post By: Warren Lake Today, 12:10 PM

Dai Sheldrake

There is no available content written by Dai Sheldrake

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Miller Falls 17B Block Plane Help

Looking for some assistance from Miller Falls folks.

I bought a lot of 6 block planes off my usual auction site. The planes were listed
Patrick C Daugherty Today, 3:46 PM

Delta Contractor's table saw Platinum Edition - USA Made?

First place I always look is is tag on motor, if corners going to be cut that’s usually where start. Well it’s where I look anyway
Carroll Courtney Today, 3:41 PM

Sandblasting

How do you achieve fine placement of the blast for more precise or delicate work?
Are the air volumes required still the same.
STUART Robertson Today, 3:40 PM

Glue Chairs

How about PU glue? Might that work? It will, reputedly, glue together almost anything ... although it might be difficult to work with and I have no idea
David Storer Today, 3:37 PM

Total Boat Epoxy?

Good afternoon guys, while back Tom help me with selecting a penetrating epoxy Total Boat. Since this is first time I ever use epoxy I like to stay with
Carroll Courtney Today, 3:29 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Dai Sheldrake

Recent Polls

Recent Forum Posts

Recent Blog Posts