Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 11:20 PM

Residential fence rules
Thread Starter: Stan Calow
I am looking for what people in other jurisdictions have dealt with. I have always understood that, in my city, fences between homes were the responsibility of the homeowner who first puts it up. And the rule was "good side out" and 6" off the property line. But after a discussion with a...
Last Post By: Jim Becker Today, 11:06 AM

Seeking Recommendation on a Bench Grinder with Specific Features.
Thread Starter: Scott Memmer
Hi, Everyone. I dearly love this forum, although I have not posted in a long time. You folks are so knowledgeable and always have such great suggestions. Here is my situation. I make a small music accessory and need to build my own saw. Without going into all the details, I've been searching for...
Last Post By: Ray Selinger Yesterday, 5:12 PM

California bans gas lawn mowers and leaf blowers after 2024
Thread Starter: Bill Dufour
Saw a sign at hoe despot and looked it up. California has banned the sale of gas lawnmowers and leaf blowers after 2024. If yours is getting tired better buy a new one in a few months. I assume they will be gone from stores by Fall. It will probably take ten to twenty years until this ban goes...
Last Post By: Doug Garson Today, 12:14 PM

Harvey COMPASS RG-1/RG-2 Universal Roller Guides Question
Thread Starter: James Cheever
All - Has anyone seen or used the Harvey COMPASS RG-1/RG-2 Universal roller guides. They look solid and would be a pretty useful addition to my shop, but the price seems way too high. I'd love to hear any feedback. Thanks.
Last Post By: Lloyd McKinlay Yesterday, 9:46 PM

Anyone with temperature controller experience?
Thread Starter: Doug Garson
I'm volunteering for a food bank and trying to set up a cold room to store produce and other perishables. The main cooling will be done by a pair of air conditioners controlled by a Coolbot which enables the air conditioners to cool the room down below the usual lower limit for air conditioners...
Last Post By: Bill Dufour Yesterday, 4:20 PM

Bob Goodwin

There is no available content written by Bob Goodwin

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Need a New Resaw Blade

Yes
3/4' is typically better for resawing and 3 tpi is really all that saw needs.
Edward Weber Today, 12:48 PM

Federal side tables

Peter, nice work. I made 6 ( wife and 5 adult kids) of those a few years ago after Steve Latta came out to the left coast for a SAPFM meeting. Same
Patrick McCarthy Today, 12:47 PM

PSA: I am alive for the next three years

Wells Fargo has banks all over Minnesota and Wisconsin now since they merged with Norwest in 1998. I have lived in Minnesota my entire life and I never
Brian Elfert Today, 12:47 PM

Safety switch test

With all due respect, this is not personal.
I think you're way off the mark.
I don't know how long or what kind of machinery you've been exposed
Edward Weber Today, 12:44 PM

HF (Bauer) carbide router bits?

I just got one from there the other day. I don't find much difference between the cheap bits and expensive ones aside from the guide bearings don't last
Cameron Wood Today, 12:42 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Bob Goodwin

Recent Polls

Recent Forum Posts

Recent Blog Posts