Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Jim Allen Today, 5:25 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Today, 8:20 PM

California bans gas lawn mowers and leaf blowers after 2024
Thread Starter: Bill Dufour
Saw a sign at hoe despot and looked it up. California has banned the sale of gas lawnmowers and leaf blowers after 2024. If yours is getting tired better buy a new one in a few months. I assume they will be gone from stores by Fall. It will probably take ten to twenty years until this ban goes...
Last Post By: Doug Garson Today, 8:15 PM

Residential fence rules
Thread Starter: Stan Calow
I am looking for what people in other jurisdictions have dealt with. I have always understood that, in my city, fences between homes were the responsibility of the homeowner who first puts it up. And the rule was "good side out" and 6" off the property line. But after a discussion with a...
Last Post By: Pat Germain Today, 4:57 PM

Seeking Recommendation on a Bench Grinder with Specific Features.
Thread Starter: Scott Memmer
Hi, Everyone. I dearly love this forum, although I have not posted in a long time. You folks are so knowledgeable and always have such great suggestions. Here is my situation. I make a small music accessory and need to build my own saw. Without going into all the details, I've been searching for...
Last Post By: stephen thomas Today, 10:33 PM

Harvey COMPASS RG-1/RG-2 Universal Roller Guides Question
Thread Starter: James Cheever
All - Has anyone seen or used the Harvey COMPASS RG-1/RG-2 Universal roller guides. They look solid and would be a pretty useful addition to my shop, but the price seems way too high. I'd love to hear any feedback. Thanks.
Last Post By: Robert Hayward Today, 6:52 PM

Brian Dickinson

There is no available content written by Brian Dickinson

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Woodturning Magazines?

Included with my last two purchases of used lathes, tools, etc. were issues of Woodturning Design, American Woodturner and Woodturning from several years
Steve Mathews Today, 10:38 PM

Seeking Recommendation on a Bench Grinder with Specific Features.

Per my earlier notes, tonight i played around with cutting a 1.5" dia piece of ultem 1000.
Also per my earlier notes, alignment is critical,
stephen thomas Today, 10:33 PM

New railings for our church

I also like the design. Minimal presence very nice design.
Andrew Hughes Today, 10:32 PM

Lumber and Sheet good markups at lumber yards

I'm just curious (I'm not complaining or trying to get everyone riled up) what the average mark up is on lumber in a yard? I'm especially curious about
andrew whicker Today, 10:29 PM

New railings for our church

Looks nice.
Leigh Betsch Today, 10:17 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Brian Dickinson

Recent Polls

Recent Forum Posts

Recent Blog Posts