Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Michael Burnside Today, 11:31 AM

Cheap Bandsaw for Resawing
Thread Starter: Jimmy Harris
I'm a hobbyist on a limited budget looking for a bandsaw, primarily for resawing. Let's say, 12" of 8/4 hard maple cut down the middle would be the maximum I would ever ask of it. I'm under the impression that I'll need a steel framed bandsaw for that. What else do I need to know? Are guides...
Last Post By: Sam Force Today, 9:43 AM

Are they building standalone car washes like crazy in your area too?
Thread Starter: Brian Elfert
They are going crazy building standalone car washes in my area. I know of at least three currently under construction nearby, and a few others that recently opened. Car washes are going up all over the Minneapolis metro area. There will easily be three times as many standalone car washes once...
Last Post By: Jim Becker Yesterday, 8:10 PM

Epoxy glue joint opened
Thread Starter: Mark Gibney
I glued up this oval Santos mahogany coffee table on Sunday. Yesterday morning, Tuesday, I placed it outside under cloudy skies in the hope that the UV to hasten the darkening of wood surface before finishing later this week. The center seam opened up. I used brand new T-88 epoxy with...
Last Post By: Mark Gibney Yesterday, 6:33 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: julian abram Yesterday, 8:32 PM

Rocks in their heads
Thread Starter: Edward Weber
https://www.ktnv.com/news/park-rangers-looking-for-two-vandalism-suspects-at-lake-mead-national-recreation-area What the ____ is wrong with some people?
Last Post By: Doug Garson Today, 12:13 AM

Bob Elliott

There is no available content written by Bob Elliott

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Monarch Unipoint Saw

think ive seen a few restored ones, look like excellent quality from the photos.
Warren Lake Today, 1:00 PM

SCM T130 bearing change

Flat pin wrench. Doc you have one for a an angle grinder? Or make one from a piece of angle iron and two hardened allen head set screws with nuts to
Bill Dufour Today, 12:59 PM

T120 shaper vibration.

hows the counterfeit storey now a days Past they were notorious for running one shift of fake everything from hand bags to car parts. It was in the billions.
Warren Lake Today, 12:59 PM

42mm chisels

Those are the ones that have been sharpened the least, and are close to their original length. The first is from the set that I purchased around 1980-
Cameron Wood Today, 12:46 PM

T120 shaper vibration.

That’s not really where I’m aiming that comment, but rather simply that one should do their research when buying on eBay.
Brian Holcombe Today, 12:46 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Bob Elliott

Recent Polls

Recent Forum Posts

Recent Blog Posts