Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Jim Allen Yesterday, 4:39 PM

Milling machine as a mortiser
Thread Starter: andrew whicker
Hi all, I don't look often, but when I do it seems there are absolutely no used mortising machines out there. Something I've always wanted (someday) was a knee mill. There's a place near me that has had a Cincinnati Contour Master for sale forever (years and years). They re build these...
Last Post By: Wes Grass Yesterday, 9:10 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 9:54 PM

Adhesive with a long open time
Thread Starter: Tim Andrews
Greetings All, I’ve done a search here, but all the threads I have seen are old. I would like a recommendation for an adhesive with a long open time for complicated glue ups, minimum 30 minutes,. I typically use Titebond 3 but would like more time for some projects. Sometimes it’s possible to do...
Last Post By: Jimmy Harris Yesterday, 9:48 AM

Harvey ST-1500 Sliding Table question
Thread Starter: Jay Houghton
I recently sold a machine I didn't need and now can repurpose that money into something else. I recently got a Sawstop and was thinking of the Harvey sliding table attachment for it. Expensive but it sure looks like the build quality is first class. You essentially get the Harvey miter gauge as...
Last Post By: Michael Burnside Yesterday, 3:27 PM

Need ideas on waterproof board to cover water damaged base of outside doors
Thread Starter: Randall J Cox
I have two exterior doors, one to the back of my house and one to my tool shed. Both are showing the effects of winter water splashing up on them at the base. The door to my shed is really bad. I don't want to replace the doors but would like to put a board over the base, like a kickplate to...
Last Post By: Patrick Curry Yesterday, 5:36 AM

Howard Dean

There is no available content written by Howard Dean

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Anyone with temperature controller experience?

I'll look at automated greenhouse systems, our contractor recommends looking at Honeywell controllers. I suspect any instrument tech could put together
Doug Garson Today, 12:58 AM

interesting mobile base brake setup on facebook

I like the casters better than choking down the chip shroud like that. Run some 11" wide poplar through there and the shroud will be full.
Richard Coers Today, 12:40 AM

Creeker's Past Week's Accomplishments

Paul - thank you for the compliment!

Michael B. - this site needs a "Like" button - i'd add a few for your bench!
Your project
stephen thomas Yesterday, 11:33 PM

storing kiln dried white and red oak outside

Hey folks,
I have a couple of stacks of white oak and one red oak that are coming out of a kiln. I don't have any more room to store it inside.
stevo wis Yesterday, 11:18 PM

Forrest Dado King 8”, WW1 & WW2 10” blade, and Jessada 10” ultra cut 80” blades

PM sent on the WW2
Zachary Hoyt Yesterday, 10:47 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Howard Dean

Recent Polls

Recent Forum Posts

Recent Blog Posts