Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Kevin Jenness Today, 4:48 PM

Cheap Bandsaw for Resawing
Thread Starter: Jimmy Harris
I'm a hobbyist on a limited budget looking for a bandsaw, primarily for resawing. Let's say, 12" of 8/4 hard maple cut down the middle would be the maximum I would ever ask of it. I'm under the impression that I'll need a steel framed bandsaw for that. What else do I need to know? Are guides...
Last Post By: John Kananis Today, 3:13 PM

Are they building standalone car washes like crazy in your area too?
Thread Starter: Brian Elfert
They are going crazy building standalone car washes in my area. I know of at least three currently under construction nearby, and a few others that recently opened. Car washes are going up all over the Minneapolis metro area. There will easily be three times as many standalone car washes once...
Last Post By: Brian Elfert Today, 4:24 PM

Rocks in their heads
Thread Starter: Edward Weber
https://www.ktnv.com/news/park-rangers-looking-for-two-vandalism-suspects-at-lake-mead-national-recreation-area What the ____ is wrong with some people?
Last Post By: Doug Garson Today, 12:13 AM

LLAMBRICH Intergrated arbor and chuck
Thread Starter: Patty Hann
Opinions, please on integrated arbor and chuck for a DP. Am looking at the LLAMBRICH Keyless chucks ... integrated 2MT shank/arbor 1/32" to 3/8" (part# JK10-MT2) 1/32" to 1/2" (JK13-MT2) Thanks
Last Post By: Jim Becker Today, 7:52 PM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Tom Yaegle Today, 9:25 PM

Gary Miklavic

There is no available content written by Gary Miklavic

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Shop Project: Finally flattening my main bench top

Looking good, can not wait to see the final photo.
Frank Necaise Today, 10:26 PM

blade insert for delta/rockwell 12/14

you can make an insert out of wood, use a Forstner bit to make a depression on the underside and super-glue some small magnets to hold it to the depression
Mike Wilkins Today, 10:10 PM

Not Recommended Jaws!

The G3 is smaller in diameter than the SN2. 3 7/16" and 3 7/8" approximately.
Robert Hayward Today, 9:59 PM

Bottom Mount 30" Drawer slides

Thanks for the responses. Drilling holes through the blum slides would be the simple solution. It's odd that they don't have them already from their catalog-
Travis Fatzinger Today, 9:48 PM

SCM T130 bearing change

Bill, I have the sockets for Fords. They are to big, will check auto part to see if there are smaller ones that may work.

Jerry, This nut
Tom Yaegle Today, 9:25 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Gary Miklavic

Recent Polls

Recent Forum Posts

Recent Blog Posts