Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 11:20 PM

Residential fence rules
Thread Starter: Stan Calow
I am looking for what people in other jurisdictions have dealt with. I have always understood that, in my city, fences between homes were the responsibility of the homeowner who first puts it up. And the rule was "good side out" and 6" off the property line. But after a discussion with a...
Last Post By: Pat Germain Today, 4:57 PM

Seeking Recommendation on a Bench Grinder with Specific Features.
Thread Starter: Scott Memmer
Hi, Everyone. I dearly love this forum, although I have not posted in a long time. You folks are so knowledgeable and always have such great suggestions. Here is my situation. I make a small music accessory and need to build my own saw. Without going into all the details, I've been searching for...
Last Post By: Ray Selinger Yesterday, 5:12 PM

California bans gas lawn mowers and leaf blowers after 2024
Thread Starter: Bill Dufour
Saw a sign at hoe despot and looked it up. California has banned the sale of gas lawnmowers and leaf blowers after 2024. If yours is getting tired better buy a new one in a few months. I assume they will be gone from stores by Fall. It will probably take ten to twenty years until this ban goes...
Last Post By: Doug Garson Today, 5:00 PM

Harvey COMPASS RG-1/RG-2 Universal Roller Guides Question
Thread Starter: James Cheever
All - Has anyone seen or used the Harvey COMPASS RG-1/RG-2 Universal roller guides. They look solid and would be a pretty useful addition to my shop, but the price seems way too high. I'd love to hear any feedback. Thanks.
Last Post By: Lloyd McKinlay Yesterday, 9:46 PM

Grease..... and not the movie....
Thread Starter: Karl Card
I have a baldor 7.5HP BALDOR 3450RPM 213T TEFC 1PH MOTOR L3709Ton my table saw. What type of grease should I look for to put grease in the grease or zirk fitting?
Last Post By: Roger Feeley Today, 3:24 PM

Bruce Pearce

There is no available content written by Bruce Pearce

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Good source if you want to try Japanese planes

Truth.

Not that i don't like to try other methods, i do.
But at this time of life i have to be careful which rabbit holes
stephen thomas Today, 5:01 PM

California bans gas lawn mowers and leaf blowers after 2024

Yes, but the ban is not on the use but only the sale of new gas powered lawnmowers etc. Commercial lawnmowers have a life expectancy of about 2500 hours.
Doug Garson Today, 5:00 PM

Residential fence rules

There is endless drama surrounding fences between houses. When I lived in Virginia, my next door neighbor had an older, wooden picket fence which was
Pat Germain Today, 4:57 PM

California bans gas lawn mowers and leaf blowers after 2024

Yard cutting is probably the biggest employer here on the lake. No one cuts their own grass. Most have already switched to cordless blowers and trimmers
Tom M King Today, 4:52 PM

Youthful Adventures

Saw that movie at the drive-in with my family. My dad was a desert racer in SoCal back then and he was familiar with some of the people in the movie.
Pat Germain Today, 4:46 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Bruce Pearce

Recent Polls

Recent Forum Posts

Recent Blog Posts