• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Dave Anderson NH

    Time for some levity

    Thread Starter: Dave Anderson NH

    With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.

    Last Post By: Jim Koepke Yesterday, 2:28 PM Go to last post
    Jacob Mac

    Hammer K3 Winner 48x48 thoughts?

    Thread Starter: Jacob Mac

    I'm kicking around getting the Hammer K3 Winner 48x48 sliding table saw. Does anyone have one? Experience with it? Better options in the $5,000 price range? I suppose the Sawstop and the Minimax SC2 are probably the other contenders. I'm tracking that used is always an option, just tough to...

    Last Post By: Jacob Mac Today, 11:00 AM Go to last post
    Michael Rutman

    Dust Collector recommendations

    Thread Starter: Michael Rutman

    Oh boy, reading the archives I can see this is not a simple question, which makes me feel good because I am completely lost. I have never owned a dust collector mostly due to inability to figure out what I need, and that needs to change. So, let me go over my shop, my needs, and then beg for...

    Last Post By: james manutes Yesterday, 1:18 PM Go to last post
    Pat Germain

    Options for Harvey Table Saw?

    Thread Starter: Pat Germain

    I've been away from woodworking for about ten years while I was restoring a car. It was something wanted to do since I was a kid and I finally got it done. Now I want to get back into woodworking and I will need a new table saw. I had been using a hot-rodded Craftsman contractor saw. It got the...

    Last Post By: Jim Becker Today, 9:36 AM Go to last post
    Thomas Colson

    How to replace Syder/Coupler on Supermax 16/32>?

    Thread Starter: Thomas Colson

    I have a Supermax 16/32 with a pretty clapped out rubber spyder-coupler. Little tiny pieces of rubber are coming out of it, which makes sense, I've used this like I stole it for the last 2 years. Any videos or instructions with pictures anywhere on how to do this that are deliberately hidden and...

    Last Post By: Thomas Colson Today, 10:11 AM Go to last post
    Brian Elfert

    I think my zero turn mower is cursed!

    Thread Starter: Brian Elfert

    I bought a used 2019 Grasshopper diesel zero turn mower with 189 hours on it last summer. I had all kinds of problems with it initially including a starter that didn't always turn over. I realized after I bought it that the mower had been buried pretty deep in mud or something as the dashboard...

    Last Post By: Brian Elfert Today, 9:05 AM Go to last post
  • Jim Koepke

    There is no available content written by Jim Koepke
  • Recent Polls

  • Recent Forum Posts

    Jacob Mac

    Hammer K3 Winner 48x48 thoughts?

    The saw arrived a week ago, shipping was pretty uneventful. A couple of little dings, but no obvious damage upon inspection. It was well packaged. And

    Jacob Mac Today, 11:00 AM Go to last post
    John TenEyck

    Delta Unisaw Blade Guard

    I use an old Sears TS guard on my Unisaw. It's mounted to an overhead arm so I can use it cutting dados. I use a shop built splitter for through cuts.

    John TenEyck Today, 10:59 AM Go to last post
    Lawrence Duckworth

    Stone foundation repair question

    ...years ago Dow Chemical had a product called Sarabond and could be used to lay an 8' jackarch w/o a steel lintel for support. ifn the stones are cleaned

    Lawrence Duckworth Today, 10:58 AM Go to last post
    andy bessette

    new bandsaw wont' cut straight

    The narrow blade that came with the machine is likely to wander in the cut, so don't expect to be able to do re-saw work with it. For that you will need

    andy bessette Today, 10:56 AM Go to last post
    John TenEyck

    new bandsaw wont' cut straight

    You might need a new blade if it's the one that came with the machine but more than likely the machine still isn't set up right. A narrow blade will

    John TenEyck Today, 10:55 AM Go to last post
  • Recent Blog Posts