Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Kev Williams Today, 3:14 PM

What 8" jointer would you get and why?
Thread Starter: Alden Peterson
I think I'm finally going to pull the trigger on an 8" jointer. I don't have one right now and I'm tired of having to planer sled/table saw sled for jointing and not getting perfect cuts on those anyways. Prices are all over the place between brands. I'm wanting helical and probably...
Last Post By: Ronald Blue Today, 2:52 PM

30w Fiber Laser Not Firing Help Please!
Thread Starter: Nick Marchesani
Hi All! My 30w fiber laser stopped firing when it was about 1/3 thru engraving an aluminum bracelet. Can anyone give some advice? I'm using ezcad2 14.9. Are there any fuses inside the Laser box? Can anyone also tell me if a dialog box opens with a Agree/Disagree dialog box when you start...
Last Post By: Kev Williams Today, 3:04 PM

"Unboxing" - Harvey G700 DC
Thread Starter: Jim Becker
I mentioned in my shop build thread that a new DC system was needed once I move in. Despite that being a few months away, I took advantage of a sale on the G700 and it arrived on Thursday. (I will say that for anyone interested in this machine...bide your time and watch for the $2499 sale price. I...
Last Post By: Steve Rozmiarek Today, 2:49 PM

Paving the driveway
Thread Starter: John K Jordan
After waiting a month for a dry spell we finally got the driveway paved yesterday. Sure creates a different look at the farm. I left some unpaved for now where I need to move heavy trucks and equipment (and because paving is not inexpensive...) My Lovely Bride was especially interested in...
Last Post By: Jim Koepke Today, 2:11 PM

What do you use 2" long 23 ga pins for?
Thread Starter: Rich Engelhardt
My PC 23 ga pin nailer uses up to 1" long pins. I use it quite a bit. So far, I haven't run across anything I'd use it on where I'd prefer it had the ability to shoot a 2" pin. What am I missing?
Last Post By: Ron Selzer Today, 3:36 PM

Debby Heyler

There is no available content written by Debby Heyler

Recent Polls
Recent Forum Posts

What do you use 2" long 23 ga pins for?

Did that back in the 80's with a Senco finish gun, pulled my hand away at the same time, never bleed. Got ring finger at inside of joint. Got to go see
Ron Selzer Today, 3:36 PM

Repaint Kitchen Cabinet Doors

Guess I'm outdated on using Oil-based paint for spraying kitchen cabinets. Basically, I cannot find any Oil-based paint locally. I sprayed these cabinets
julian abram Today, 3:36 PM

Best beginner spray setup

Jeff Jewitt suggests that the finest finishes are achieved using a compressor based system. I too believe the hvlp systems offer less control. It's
Prashun Patel Today, 3:28 PM

Bosch 12" miter quick release holddown

Subscribed; have wondered the same thing - could really use a quick release hold down here!

Here is an old thread I found but didn't seem
Josh Molaver Today, 3:26 PM

Subscription

...notify me of changes.

Not happening for me, specifically in "time for levity.
Jim Allen Today, 3:20 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Debby Heyler

Recent Polls

Recent Forum Posts

Recent Blog Posts