• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Dave Anderson NH

    Time for some levity

    Thread Starter: Dave Anderson NH

    With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.

    Last Post By: Dave Anderson NH Today, 2:47 PM Go to last post
    ken hatch


    Thread Starter: ken hatch

    I asked this question on another thread. What's with the multiple bevels, over the last couple or three weeks I keep seeing mention of primary, secondary, and even tertiary bevels. Most of the time Rob Cosman is also given credit as in "sharpened as Rob Cosman does". Why? Is it a honing guide...

    Last Post By: Bob Jones 5443 Yesterday, 4:04 PM Go to last post
    John Pariseau

    Load Center for "new" shop

    Thread Starter: John Pariseau

    I completed (passed final inspection) last October (2019), and I'm getting ready to start electrifying my shop. I had decided early on pulling a building permit that included electric, was too much for me to do in one pass - I'm very glad I made that decision. I've done some research here and on a...

    Last Post By: Jim Becker Yesterday, 7:38 PM Go to last post
    Todd Sebek

    Help buying my first bandsaw(s)

    Thread Starter: Todd Sebek

    Hey everyone, I am new to this forum but have researched through it for a while. What a great resource. I need y’all’s advice. I am an amateur/beginner woodworker but truly value quality tools. My understanding wife has allowed me to try to purchase “forever” tools this year. Again, I’m an...

    Last Post By: Mike Kees Yesterday, 9:02 PM Go to last post
    Dan Kraakenes

    Veritas LA/BU planes or Custom planes?

    Thread Starter: Dan Kraakenes

    Im considering upgrading my single plane to more dedicated 4,5,7 planes. Im currently used to a #4, but I have to large hands for it, so was first thinking of upgrading to a 4 1/2. But.. then again I am wondering if I should go for the Low Angle / Bevel up planes or the "Custom" Veritas...

    Last Post By: Dan Kraakenes Today, 3:51 PM Go to last post
    Frederick Skelly

    Do YOU use handscrew clamps?

    Thread Starter: Frederick Skelly

    There's another thread where a guy in europe is buying a bunch of clamps and asked for advice. There's some back and forth about wooden handscrew clamps. (Like these) One man says everybody has some but most people don't use them often. Another man says he uses them for a lot of things. I didnt...

    Last Post By: John K Jordan Yesterday, 8:36 PM Go to last post
  • lowell holmes

    There is no available content written by lowell holmes
  • Recent Polls

    Which fence: (Votes: 4)

    1. Delta Biesemeyer 78919B Type 2 (Votes: 0)

    2. SawStop TGP2-FA (Votes: 3)

    3. Something else (Votes: 1)

  • Recent Forum Posts

    Mike Henderson

    "retrofit" recessed lights

    I installed those retrofit LED can lights in my house. No serious problems. They are brighter than the lights I had in the cans so I had to put some

    Mike Henderson Today, 3:51 PM Go to last post
    Dan Kraakenes

    Veritas LA/BU planes or Custom planes?

    So.. If one has a Scrub and a Shooting plane.

    Which of the three Bevel Up / Low angle Smoother, Jack, Jointer, is the most "useless"

    Dan Kraakenes Today, 3:51 PM Go to last post
    tom lucas

    Hello and thank you

    Actually, Pat, Thompson sells both v and u fluted gouges. Sometimes he is out of stock on one type or another, but he sells both plus some specialty

    tom lucas Today, 3:51 PM Go to last post
    Andrew Seemann

    Vintage Cars

    I friend of mine had a Porsche 931 (924 Turbo), and that is what I remember about it. It cornered like it was on rails, but you felt every single pebble,

    Andrew Seemann Today, 3:48 PM Go to last post
    David Eisenhauer

    Mortise and tenon questions / musings

    Jim - As I said above, a router plane does indeed create coplanar tenon cheeks, but the use of a router plane for final thicknessing can slow the whole

    David Eisenhauer Today, 3:40 PM Go to last post
  • Recent Blog Posts