• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Keith Outten

    Microfence FreeStuff Drawing 9-20-2019

    Thread Starter: Keith Outten

    FreeStuff Drawing Info: Microfence Original Edge-Guide for the router of your choice with their Microfence Stop Collar set. ($249.95 Retail Value) Rich Wedler Phone 818-683-0330 www.microfence.comOur quarterly newsletter + Sale notifications + Free drawings + Free shipping coupon (Micro...

    Last Post By: Michael Alu Today, 2:36 PM Go to last post
    Jamie Buxton

    Cold creep in modified PVA glues?

    Thread Starter: Jamie Buxton

    Ordinary wood glue, for instance Titebond original, is infamous for cold creep. Does anybody know if the modified PVAs like Titebond II or Titebond III creep less?

    Last Post By: Andrew Hughes Yesterday, 11:20 PM Go to last post
    Michael Gantz

    Hanging EMT conduit in new shop.

    Thread Starter: Michael Gantz

    I'm currently in the process of building a 24' x 36' shop with 10' ceilings. The walls are 2" x 6" studs and the cavities are filled with cellulose insulation. The walls are covered in 1/2" drywall. My intention is to minimize wall penetrations to keep air leaks to a minimum. The plan is to...

    Last Post By: Jon Nuckles Today, 1:45 PM Go to last post
    Greg Parrish

    Leigh D4R Pro

    Thread Starter: Greg Parrish

    I just joined the crowd and wanted to get some input going on tips, websites, videos, etc. that might not show up immediately in searches but that others found valuable to get going when they first started using this jig. Anything beyond the Leigh website that is a must read or watch? i donít...

    Last Post By: Charles Lent Today, 11:06 AM Go to last post
    Dan Friedrichs

    Hardwood flooring over particle board subfloor?

    Thread Starter: Dan Friedrichs

    I'm tearing up carpet and putting down 3/4" solid hardwood, but have found that the subfloor is 3/4" particle board (yes, particle board, not OSB) on top of 1/2" plywood. From googling, I've learned this was common in the 70s-80s to bring a carpeted floor up to the same level as other tile...

    Last Post By: Frank Pratt Today, 1:45 PM Go to last post
    Dave Lehnert

    New Zero Turn Mower

    Thread Starter: Dave Lehnert

    Starting to think about a new Zero Turn Mower. I now own a Toro 52" with a 19 Hp Kawasaki that I have been happy with. Mow 2 1/2 acr all flat. What brand have you been happy with? More important. Is there a brand you have had trouble with? Parts hard to get etc.....

    Last Post By: Brad Chenoweth Today, 12:22 PM Go to last post
  • Anthony S Martin

    There is no available content written by Anthony S Martin
  • Recent Polls

    What color do you pick? (Votes: 72)

    1. Black (Votes: 16)

    2. Blue (Votes: 9)

    3. Green (Votes: 4)

    4. Orange (Votes: 3)

    5. Red (Votes: 27)

    6. Yellow (Votes: 3)

    7. White (Votes: 3)

    8. Other (Votes: 7)

  • Recent Forum Posts

    Lisa Starr

    Rust prevention

    I just apply with a rag and hand buff with a clean rag when dry. It takes a little time, but I find it enjoyable when I'm too tired to actually work

    Lisa Starr Today, 3:41 PM Go to last post
    Lisa Starr

    Anyone familiar with Pex tube and connectors?

    I didn't have a slab to deal with, as we have a "full" basement. Even then, though it takes more material, I installed a home run system when

    Lisa Starr Today, 3:33 PM Go to last post
    Randy Heinemann

    Bandsaw circle jig

    If you don't want to make one, Carter Bandsaw sells one that is good and also has a separate attachment that works for cutting out bowl blanks if you're

    Randy Heinemann Today, 3:30 PM Go to last post
    Randy Heinemann

    sharpening scapers

    Christophe Schwarz and Michael Peckovich (Fine Woodworking) both have great articles on sharpening scrapers that are very clear and give a lot of direction

    Randy Heinemann Today, 3:28 PM Go to last post
    Tom Blank

    Good examples of file storage?

    I built two trays that stack and fit in the file, scraper, and diamond hone drawer. Bases are 1/8" Masonite, ends and dividers are 1/4".

    Tom Blank Today, 3:25 PM Go to last post
  • Recent Blog Posts