• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Ken Fitzgerald

    Shop lighting......

    Thread Starter: Ken Fitzgerald

    Here's an article that answers a lot of shop lighting questions that are so often asked here. http://www.sawmillcreek.org/content.php?146-Lighting-the-Small-Workshop-by-Jack-Lindsey

    Last Post By: Mike OMelia Today, 3:16 PM Go to last post
    Erich Weidner

    Squaring Up Really Long Boards... Tips?

    Thread Starter: Erich Weidner

    I have a few dozen long boards I need to glue up into large panels. (11' to 16' for each section). They will be about 32" wide. I'm gluing up from 1 x 6 S4S stock. (So nominally 3/4" x 5-1/2"). They of course all have some bow, cup, or twist. I don't care at all about the look of one flat face...

    Last Post By: Erich Weidner Yesterday, 11:41 PM Go to last post
    steven c newman

    A new Desk for me

    Thread Starter: steven c newman

    "old" one is cramped, small drawers....not enough room for the computer I am using...so. Came up with a rough "Plan".. Picked up about 40bf of Ash....($20.....) Then drew up a better Plan... More as a guide, than anything carved in stone....(already a few design changes have been made..)...

    Last Post By: steven c newman Today, 7:54 PM Go to last post
    Alan Lightstone

    Soundproofing for workshop entry wall

    Thread Starter: Alan Lightstone

    Finally getting a contractor to put the walls up in my workshop. I've been looking at a variety of techniques for soundproofing the walls (it's an interior wall to my garage, the exterior walls are cinderblock and aren't being done now. There will be a double outside rated entry door from the...

    Last Post By: Frank Pratt Today, 2:52 AM Go to last post
    Bram de Jong

    Moxon vise design "review"?

    Thread Starter: Bram de Jong

    Hi everyone, Since a while I've been slowly working on a "fully parametric" version of a Moxon vise design in Fusion 360. Fully parametric meaning you can change all the sizes of width, height, thread diameter etc etc with the model still working. But I'd like some review of the model itself...

    Last Post By: Derek Cohen Today, 7:34 PM Go to last post
    Malcolm McLeod

    Good Scotch deserves a good home

    Thread Starter: Malcolm McLeod

    All good Scotch deserves a good home! Working on a tight deadline, this bar-back went into place last night for a fund-raiser on Saturday. Curly Cherry and Beech in what turned into a Stickley-meets-modern (I hope) design. I’d love to claim it has every dimension set from a Golden ratio,...

    Last Post By: Bill Carey Today, 6:27 PM Go to last post
  • Scott Winners

    There is no available content written by Scott Winners
  • Recent Polls

  • Recent Forum Posts

    stan kern

    shaper knives 1.25 shaft size

    I have sold my poitras model 3000 shaper and now the task of trying to sell all
    the carbide knives.all my carbide knives are USA carbide and in

    stan kern Today, 9:52 PM Go to last post
    stan kern

    100 watt laser tube replacement

    I have a new 10000hr RECI 100watt replacement tube rated at 118.9w
    bought as I thought my laser 100watt was failing, turned out it
    was the

    stan kern Today, 9:48 PM Go to last post
    Patrick Kane

    Planer design differences

    Jason,

    The blade life is nothing short of incredible; however, the hype of “tearout free” is crap. I consistently get tearout with the

    Patrick Kane Today, 9:33 PM Go to last post
    Peter Blair

    Don't know

    I really don't know what to do with this burls. All I know is the small one appears to be Douglas Fir. the other 2 may be Pine I am guessing because there

    Peter Blair Today, 9:31 PM Go to last post
    Ron Citerone

    What’s the Max board width for 12” bandsaw?

    I have done this with low power table saws before. 10" can cut 3" high. Just do it in 3 1" steps keeping the jointed side against the

    Ron Citerone Today, 9:15 PM Go to last post
  • Recent Blog Posts