• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Patrick Walsh

    Vintage Martin T75 restoration

    Thread Starter: Patrick Walsh

    So I have a opportunity to purchase the above machine for a fair deal from my employer. I am aware of the phenolic guides being pop riveted I the the sliding table along with not availible for replacement. So my question is as follows to those in the know with regard to the phenolic ways....

    Last Post By: Bryan Lisowski Yesterday, 9:09 PM Go to last post
    Mike Heidrick

    Pole Barn 40X64X16

    Thread Starter: Mike Heidrick

    Signed a contract yesterday with S&L Builders out of Indiana for a 40X64X16 Pole Barn with a 10X24 porch. Build date August 18, 2014. Plan to install Pex for raidant floor heat. Concrete slab 5" thick. Also doing 1.5" closed cell foam under the pad. Built on Laminated posts in ground. Will...

    Last Post By: Mike Kees Yesterday, 9:09 PM Go to last post
    Patrick Walsh

    1982 Martin T-23

    Thread Starter: Patrick Walsh

    And so it seems it begins again. The T-75 isn’t even technically done and I have a new project. I’m not gonna go all buggy on this one “just yet” if ever. I will 100% go all the way through the machine and make sure it is 100% fully functional to the 9’s. 10’ for me if it was a term. If anything...

    Last Post By: Joe Calhoon Yesterday, 11:51 PM Go to last post
    Travis Conner

    Is there money in woodworking?

    Thread Starter: Travis Conner

    Other than making kitchen cabinets, is there money in it? I've always kept it as a hobby. I once heard of a guy who won the lottery say he's going to keep wood working until the money runs out. Lol

    Last Post By: John Makar Yesterday, 1:35 PM Go to last post
    Ron Bontz

    Which CNC

    Thread Starter: Ron Bontz

    Looking at CNC routers. Leaning more toward water cooled spindles, as I don't wish to buy twice. Something in the smaller 25 x 36 size range, but with a 4th axis option. I will be using it on wood primarily and occasionally aluminum. There are many options out there with price ranges around 5,000...

    Last Post By: Ron Bontz Yesterday, 1:26 PM Go to last post
    Ken Fitzgerald

    Shop lighting......

    Thread Starter: Ken Fitzgerald

    Here's an article that answers a lot of shop lighting questions that are so often asked here. http://www.sawmillcreek.org/content.php?146-Lighting-the-Small-Workshop-by-Jack-Lindsey

    Last Post By: Bill Webster Yesterday, 9:51 PM Go to last post
  • Laurent Marshall

    There is no available content written by Laurent Marshall
  • Recent Polls

    What's your opinion? (Votes: 20)

    1. It's a shame, that could have been some really nice wide panels. (Votes: 17)

    2. Yesssssss, the world can never have enough heavily checked cookie tables. (Votes: 3)

  • Recent Forum Posts

    bill epstein

    Featherboards

    Soon after I posted about making and using feather boards I realised I hadn't mentioned using a Strong Back with but it occurred to me the OP might be

    bill epstein Today, 12:50 AM Go to last post
    orren countin

    Where find anti-kickback A28414 for Unisaw?

    Where can I find this Delta Unisaw anti-kickback pn A28414? Every site I visit shows that part is no longer available which is surprising since its for

    orren countin Today, 12:48 AM Go to last post
    Bill Dufour

    Featherboards

    I like the spring loaded "board buddies" wheels with adjustable downforce and ratchet one way action. They also make two way ones for shaper

    Bill Dufour Today, 12:44 AM Go to last post
    Bill Dufour

    Need help getting keyed chuck off Delta Drill press

    Lower quill all the way. There should be two slots on opposite sides for a wedge near the top.
    If not that looks like a threaded collar to drive

    Bill Dufour Today, 12:40 AM Go to last post
    Andrew More

    Best Dust Collector Modification Ever!

    Since I'm there, and I've spoken to my son, and he is capable of doing exactly that, I'm not sure what else to say. I'll agree the 1 1/2 year old is

    Andrew More Today, 12:37 AM Go to last post
  • Recent Blog Posts