Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Dave Zellers Yesterday, 9:10 PM

VFD for 7.5 hp 3 phase to run on 220 single phase
Thread Starter: Mike Leiferman
Anyone with any experience running a 7.5 hp 220 volt 26 amp 3 phase from a VFD powered by 220 single phase? I would like to know a) what specific vfd you are using if you recommend it, b) any issues I should be aware of The motor is driving a 1995 Lazzari Tema 3000i. The alternative for me...
Last Post By: Mike Leiferman Yesterday, 11:53 PM

How to replace Syder/Coupler on Supermax 16/32>?
Thread Starter: Thomas Colson
I have a Supermax 16/32 with a pretty clapped out rubber spyder-coupler. Little tiny pieces of rubber are coming out of it, which makes sense, I've used this like I stole it for the last 2 years. Any videos or instructions with pictures anywhere on how to do this that are deliberately hidden and...
Last Post By: Jerry Bruette Yesterday, 4:13 PM

Help Me Pick a Plow Plane or Is It a Plough Plane
Thread Starter: Thomas McCurnin
Typical use will be on 3/4 to 7/8" stock planing on edge for a a 1/4" groove about 3/8" deep for frame and panel construction. I'll also be using it for grooving a post, usually about 1.5" x 1.5" is typical, again to accept a panel for frame and panel construction. It needs to go both directions,...
Last Post By: Derek Cohen Yesterday, 7:45 PM

I hate rusty saws, but...
Thread Starter: Richard Hutchings
I just saw an ad for 7 rusty saws for $25 and I may not be able to resist. One has the thumbhole but broken horn. It might be worth buying the whole lot but I'll have to get better at cleaning them up. I hate the mess. Hopefully someone will buy them before I decide to bite the bullet.
Last Post By: Maurice Mcmurry Yesterday, 9:51 AM

Solid Walnut bookshelf dados - is glue enough?
Thread Starter: Bill Brammer
Building 6 ft high, 28 in wide, 12 inch deep solid 3/4 inch walnut bookshelf , no adjustable shelves. I have dados for all shelves. The sides are a little bowed, requiring some pressure with clamps to pull them together with the dados. Not a ton, but some. I'm trying to decide if I need to add...
Last Post By: Jim Becker Yesterday, 10:58 AM

Zachary Hoyt

There is no available content written by Zachary Hoyt

Recent Polls
Recent Forum Posts

Bailey No. 4C Smoothing Plane, Type 10, Restored, Tuned-up, and Ready to Use

Jim - I have decided to gift this to myself. Will send out payment tomorrow.
Doug Weiner Today, 12:42 AM

cub cadet older LTX-1142 Hydrastatic, start issue

went to do a second cut and the mower would not start. Tried it a number of times. Was picking up new blades and a gasket so grabbed a battery same
Warren Lake Today, 12:28 AM

Options for Harvey Table Saw?

Both the 2hp & 3hp Harvey table saws are at excellent prices - you managed to save your fingers using that hot rodded Craftsman, you will be fine
Dave Roock Today, 12:14 AM

VFD for 7.5 hp 3 phase to run on 220 single phase

Jared -
you know more about these than I do. The unit is described as having 50 amp output, so if halved, would be 25 amp. But this saw is replacing
Mike Leiferman Yesterday, 11:53 PM

Flattening stones

All true!

The one thing I will mention is that for whatever reason, sharpening knives a lot on my Arkansas stones will bring the Washitas
Luke Dupont Yesterday, 11:37 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Zachary Hoyt

Recent Polls

Recent Forum Posts

Recent Blog Posts