• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Michael Arruda

    Home Depot return policy change without notification

    Thread Starter: Michael Arruda

    Hello all, I had some small items left over from various things I've done around the house recently and decided to gather them up to take back to Home Depot. These items were purchased at various times over the past couple weeks and I of course misplaced my receipts. Meaning they got washed,...

    Last Post By: william watts Today, 1:05 AM Go to last post
    John McGovern

    Table Saw Questions

    Thread Starter: John McGovern

    Hi All, I've been lurking in the weeds for some time and have found this venue to be the most knowledgeable, helpful, and courteous forum on the block. And, I know this question has been asked and answered so many times, but I hope you all have the patience for one more dip to the well to answer...

    Last Post By: Thomas McCurnin Yesterday, 7:24 PM Go to last post
    Carl Beckett

    Dust collection barrel

    Thread Starter: Carl Beckett

    What is everyone using for a dust collection barrel? I have a heavy duty plastic trash can I put a gasket on. But it 'implodes' at times. Before I go messing with reinforcement, maybe I should just ditch it all together for something more suitable (ideally cheap and readily available locally). ...

    Last Post By: Tom Bender Yesterday, 5:15 PM Go to last post
    Carl Beckett

    Tablesaw dust collection hood

    Thread Starter: Carl Beckett

    Well, after a weekend working with black walnut I have GOT to improve my tablesaw dust collection. Which means time to put the blade guard/collection hood at the top of the project list. The support arm will be home made. The guard/hood can be either home made or purchased, but since I want to...

    Last Post By: Tom Bender Yesterday, 7:23 PM Go to last post
    Tom Trees

    Suitable relay for three wire control on a VFD

    Thread Starter: Tom Trees

    Hello folks I have been walking through the steps with another forum member on setting up a VFD for his saw. Unfortunately the VFD does not have a relay OR COMMON for three wire control/push button station. Can any of you guys point me in the right direction to find a suitable relay for him? ...

    Last Post By: David L Morse Today, 5:01 AM Go to last post
    Steve Rozmiarek

    Good quality mobility bases?

    Thread Starter: Steve Rozmiarek

    Anyone have recommendations on decent quality and reasonably priced mobility bases for table saws? I haven't paid any attention to the market in years, googled yesterday and was a little shocked at the prices I saw. Last I remember, they were half of what I'm seeing now. Bases for would cost...

    Last Post By: Randall J Cox Today, 10:55 AM Go to last post
  • Steve Middleton

    There is no available content written by Steve Middleton
  • Recent Polls

  • Recent Forum Posts

    Mel Fulks

    Recommendation for indoor grow lights?

    I use just one Costco light hanging close to cieling . Three seed flats rest on news paper on book case. Lights should be pretty close. Most important

    Mel Fulks Today, 1:42 PM Go to last post
    Prashun Patel

    Tenon wedge parallel to long cheek?

    In many situations the cheek of your tenon runs parallel to the grain of the mortised piece. Driving a wedge parallel to the grain of the mortised piece

    Prashun Patel Today, 1:39 PM Go to last post
    Michael Todrin

    3 phase motor question

    Got it up and running! Thanks everyone for the help. I ended up taking apart all the connections, cleaning and tightening and it all works. Something

    Michael Todrin Today, 1:21 PM Go to last post
    Steve Voigt

    Stupid Frame and Panel Question

    Hi Dave, I agree that it is better to track down the source of misalignment, and then if all else fails fix it on an ad hoc basis (as you're already doing),

    Steve Voigt Today, 1:21 PM Go to last post
    Steve Wurster

    Ripping Blade

    I also recommend the Freud Glue Line Rip blade or the Freud Heavy Duty Rip blade; I ran both on my old Ridgid TS 3650, which was not a very powerful saw.

    Steve Wurster Today, 1:18 PM Go to last post
  • Recent Blog Posts