• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Michael Arruda

    Home Depot return policy change without notification

    Thread Starter: Michael Arruda

    Hello all, I had some small items left over from various things I've done around the house recently and decided to gather them up to take back to Home Depot. These items were purchased at various times over the past couple weeks and I of course misplaced my receipts. Meaning they got washed,...

    Last Post By: Jon Nuckles Yesterday, 11:05 PM Go to last post
    Tom Trees

    Suitable relay for three wire control on a VFD

    Thread Starter: Tom Trees

    Hello folks I have been walking through the steps with another forum member on setting up a VFD for his saw. Unfortunately the VFD does not have a relay OR COMMON for three wire control/push button station. Can any of you guys point me in the right direction to find a suitable relay for him? ...

    Last Post By: Tom Trees Yesterday, 2:31 PM Go to last post
    Tim M Tuttle

    Jointer Safety

    Thread Starter: Tim M Tuttle

    I've been milling up a lot of white oak the past two nights. While I was using my jointer I started to ponder safety. For something like the table saw there are a lot of common safety procedures/dos/donts. A lot more than a jointer which makes sense as there are a lot more variables with the...

    Last Post By: Carl Beckett Today, 6:20 AM Go to last post
    Ronald Blue

    Two Year Old Camaster Stinger III

    Thread Starter: Ronald Blue

    I have a locally available Camaster Stinger III. It's a 4 X 8 machine with a three head setup. Whats the benefit of the three head arrangement? Is it an alternative to an ATC system? What's a fair price? He says it was $18,000 new. He's discounted it a lot from that amount. Nearly half. He did say...

    Last Post By: Keith Outten Yesterday, 8:30 PM Go to last post
    Steve Rozmiarek

    Good quality mobility bases?

    Thread Starter: Steve Rozmiarek

    Anyone have recommendations on decent quality and reasonably priced mobility bases for table saws? I haven't paid any attention to the market in years, googled yesterday and was a little shocked at the prices I saw. Last I remember, they were half of what I'm seeing now. Bases for would cost...

    Last Post By: Randall J Cox Yesterday, 10:55 AM Go to last post
    John Sincerbeaux

    Vacuum Fence for Slider

    Thread Starter: John Sincerbeaux

    Finally finished my vacuum tall fence for my slider. Made of commercially available parts from companies in the CNC industry. Aluminum T-slot plate 16 x 24 4) 4 x 4 aluminum pods pneumatic switch powered by vacuum pump from Vacuum clamping systems. The objectives for this fence were...

    Last Post By: Jeff Bartley Yesterday, 7:46 PM Go to last post
  • Jack Frederick

    There is no available content written by Jack Frederick
  • Recent Polls

  • Recent Forum Posts

    Don Parker

    Steam Bending Osage Orange


    you asked in another sub forum for input from guitar builders. As one of those, let me say that we probably can’t offer

    Don Parker Today, 6:46 AM Go to last post
    Jack Lilley

    Advice/direction needed Epilog

    I purchased an Epilog, Legend 32, 50 watt engraver about 3 yrs ago. It had been included with equipment from a business that the local Amish community

    Jack Lilley Today, 6:31 AM Go to last post
    Carl Beckett

    Dedicated Table Router


    I just replaced the bearings in mine, after what I thought was too little use.

    Carl Beckett Today, 6:24 AM Go to last post
    Carl Beckett

    Jointer Safety

    +1 on minimal pressure and sharp knives (this is similar to pocket knife safety, the easier it cuts the less built up energy to go the wrong way).

    Carl Beckett Today, 6:20 AM Go to last post
    Curt Harms

    Weather station, any favorites?

    Kev, does this device have an I.P. address on your network? I have a different Ambient Weather device that uses their internet bridge thingy. I'm able

    Curt Harms Today, 6:07 AM Go to last post
  • Recent Blog Posts