Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Jim Allen Yesterday, 5:25 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 8:20 PM

California bans gas lawn mowers and leaf blowers after 2024
Thread Starter: Bill Dufour
Saw a sign at hoe despot and looked it up. California has banned the sale of gas lawnmowers and leaf blowers after 2024. If yours is getting tired better buy a new one in a few months. I assume they will be gone from stores by Fall. It will probably take ten to twenty years until this ban goes...
Last Post By: Bill Dufour Today, 12:05 PM

Residential fence rules
Thread Starter: Stan Calow
I am looking for what people in other jurisdictions have dealt with. I have always understood that, in my city, fences between homes were the responsibility of the homeowner who first puts it up. And the rule was "good side out" and 6" off the property line. But after a discussion with a...
Last Post By: Brian Elfert Today, 9:16 AM

Seeking Recommendation on a Bench Grinder with Specific Features.
Thread Starter: Scott Memmer
Hi, Everyone. I dearly love this forum, although I have not posted in a long time. You folks are so knowledgeable and always have such great suggestions. Here is my situation. I make a small music accessory and need to build my own saw. Without going into all the details, I've been searching for...
Last Post By: Ray Selinger Today, 11:51 AM

Harvey COMPASS RG-1/RG-2 Universal Roller Guides Question
Thread Starter: James Cheever
All - Has anyone seen or used the Harvey COMPASS RG-1/RG-2 Universal roller guides. They look solid and would be a pretty useful addition to my shop, but the price seems way too high. I'd love to hear any feedback. Thanks.
Last Post By: Lloyd McKinlay Today, 12:46 AM

Jim Lane

There is no available content written by Jim Lane

Recent Polls
Would you borrow a tool from someone? (Votes: 71)
Recent Forum Posts

Maintenance requirements for ceramic stones?

Chris Schwarz has a blog entry on this topic that he posted just yesterday. He really substantiates his conclusions and cuts through (pun intended) the
Mike Brady Today, 12:09 PM

California bans gas lawn mowers and leaf blowers after 2024

I saw a video of modern crash testings a car from 1930? The seats ripped off the floor and slammed into the dashboard behind the crash test dummies.
Bill Dufour Today, 12:05 PM

Left lane

In California the #1 lane is the high speed lane. Pull into #2 if someone is coming up on your tail. get more then five? cars behind you and pull over
Bill Dufour Today, 11:58 AM

California bans gas lawn mowers and leaf blowers after 2024

transmissions should be manual. 12,000 cars were stolen in toronto by punk ass kids in 2023. Most of them can use a computer and steal your car in 1
Warren Lake Today, 11:58 AM

Gaps In Cutting Board Strips

Thanks Bryan, great tip to plane the jointed face to make sure they're co-planar. I do get a better surface off the planer than the jointer for sure.
Adam Daniel Today, 11:57 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Jim Lane

Recent Polls

Recent Forum Posts

Recent Blog Posts