Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Kevin Jenness Today, 12:14 PM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: John Kananis Today, 10:24 AM

Need ideas on waterproof board to cover water damaged base of outside doors
Thread Starter: Randall J Cox
I have two exterior doors, one to the back of my house and one to my tool shed. Both are showing the effects of winter water splashing up on them at the base. The door to my shed is really bad. I don't want to replace the doors but would like to put a board over the base, like a kickplate to...
Last Post By: Stan Calow Today, 9:20 AM

Hot water sulfur smell solutions
Thread Starter: Ron Citerone
My cottage is on well water. Several years ago we started with the dreaded sulfur smell, hot water only. I had a plumber replace the anode. Smell came back eventually. I found the model of the anode he installed and see that is just aluminum. Seems like the one I need is aluminum/zinc? Has...
Last Post By: Bill Howatt Today, 9:43 AM

Epoxy glue joint opened
Thread Starter: Mark Gibney
I glued up this oval Santos mahogany coffee table on Sunday. Yesterday morning, Tuesday, I placed it outside under cloudy skies in the hope that the UV to hasten the darkening of wood surface before finishing later this week. The center seam opened up. I used brand new T-88 epoxy with...
Last Post By: John Kananis Today, 4:01 PM

Vectric Software V12 Now Available
Thread Starter: Michael Burnside
I was talking with friend over the weekend and they were unaware that V12 has been released. So, I figured I would post here in case someone wasn't aware of this news. In general the upgrades look good overall. I personally upgraded my version of Vcarve Pro.
Last Post By: Grant Wilkinson Today, 12:08 PM

Maurice Ungaro

There is no available content written by Maurice Ungaro

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Systainers?

Tom, Systainers help me when I have to pack tools for work, if I only worked in my shop I wouldn’t have a use for them

Stack a few systainers
Rod Sheridan Today, 4:17 PM

Epoxy glue joint opened

Mark, interesting that it closed back up. Did you move it to a different spot or flip it over by chance? Or is it sitting in the same spot and orientation
John Kananis Today, 4:01 PM

Dewalt DW735 Planer for short hardwood boards?

I had my 735 about 15 or 20 years before I sprung for a floor model. I never got rid of it, still in the back room... just in case. Great planer, punches
John Kananis Today, 3:59 PM

Can't Post

Rob

Try again. Looks like we may have had a temporary glitch (about 10 minutes) with our internet provider. Let me know if you continue
Jackie Outten Today, 3:44 PM

Jobsite jointer

Been using this further, including truing the edge of a ~10' 2X6. I set the fence to act a a kind of hold down to help keep the piece in place while
Cameron Wood Today, 3:39 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Maurice Ungaro

Recent Polls

Recent Forum Posts

Recent Blog Posts