Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Sawstop Injury I didn't think this could happen.
Thread Starter: Robert Engel
I might be a bit concerned if this happened to me.
Last Post By: jack forsberg Today, 8:21 AM

20x28 workshop build
Thread Starter: Thomas Crawford
HOA approved yesterday, tentative start date right after the new year. I've had a couple other threads in here but I'll use this one for all the build pics. Details: 20'x28' (560 sq ft for the mathematically challenged) 10' sidewalls vaulted hip roof lots of natural light concrete...
Last Post By: eugene thomas Yesterday, 10:38 PM

Speedy 400 Ceramic tube replacement/refurb
Thread Starter: Bryce Mccloud
Hi there laser community. I know a lot of you have a great deal of experience with the various options out there and have been down these roads before me. Hoping to get a little advice. What options you have found to replace/repair a Trotec ceramic laser tube? Mine's has a 120watt tube...
Last Post By: Mike Null Yesterday, 3:41 PM

Working on another Project..maybe
Thread Starter: steven c newman
A small, three drawer chest of drawers, that my 8 yr old Grandson can use.....will try to build as careful as I can, so I don't spring any "leaks":eek: usually, a Frame & Panel case is made.....rather than a glued up slab. Unable to resaw the 2 x4s down into 4/4 x 3" that I like to...
Last Post By: steven c newman Yesterday, 10:11 PM

Reasonably priced chisels?
Thread Starter: Brandon Thill
Looking for a 4 or 5 piece bench chisel that won't be unduly expensive. I've been looking at the Lee Valley and Narex, and even the Buck ones at HD. Any advice?
Last Post By: Jim Koepke Yesterday, 11:25 AM

Suggestions for laptop for son as a college freshman?
Thread Starter: Kevin Womer
We understand a laptop is a necessity these days in college. In my day, it was notebooks and tape recorders. He has used a school provided Chromebook in high school and it was constantly having issues which the school would address, but in college he will be on his own. Reliability would be the...
Last Post By: Jim Becker Today, 8:20 AM

dennis thompson

There is no available content written by dennis thompson

Recent Polls
Do you wear a breathing mask when sharpening? (Votes: 72)

Never, or almost never (Votes: 61)

Seldom (Votes: 4)

Usually (Votes: 5)

Always, or almost always (Votes: 2)
Recent Forum Posts

Filling cracks on a table top

Use a little clear epoxy to fill just proud and a scraper to level after it's cured. Re-coat with the Arm-R-Seal to complete.
Jim Becker Today, 8:27 AM

A Different Stove Question

Given that...it's interesting how ranges have lower BTU figures for Propane use vs Natural Gas use...
Jim Becker Today, 8:24 AM

Bridge City Tools, John Econamaki

Your skepticism is clouded by your impression or experience of those cheap imports from China. Those cheapos are no good because the importers specify
Simon MacGowen Today, 8:24 AM

Counter-deep over-fridge panel....no side panel support. How?

Rich makes a really good point...and the client should be asked about that.
Jim Becker Today, 8:22 AM

Sawstop Injury I didn't think this could happen.

Yet another high-tech gizmo to dazzle those who have gadgetitis! The point is it STILL cannot protect you from a kickback (one of the major injury risks
jack forsberg Today, 8:21 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

dennis thompson

Recent Polls

Recent Forum Posts

Recent Blog Posts