• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Dave Anderson NH

    Time for some levity

    Thread Starter: Dave Anderson NH

    With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.

    Last Post By: Ed Aumiller Yesterday, 11:45 AM Go to last post
    Jacob Mac

    Hammer K3 Winner 48x48 thoughts?

    Thread Starter: Jacob Mac

    I'm kicking around getting the Hammer K3 Winner 48x48 sliding table saw. Does anyone have one? Experience with it? Better options in the $5,000 price range? I suppose the Sawstop and the Minimax SC2 are probably the other contenders. I'm tracking that used is always an option, just tough to...

    Last Post By: Chris Parks Yesterday, 8:24 PM Go to last post
    John TenEyck

    My OneFinity has Landed

    Thread Starter: John TenEyck

    After a long 8 weeks and 5 days my Journeyman was delivered by UPS this past Tuesday. Fortunately, everything arrived in good shape. I have to say, 1F has made assembly of the main unit very easy. They have a well written, easy to follow, assembly manual. After unpacking the three boxes it took...

    Last Post By: John TenEyck Yesterday, 8:59 PM Go to last post
    Pat Germain

    Options for Harvey Table Saw?

    Thread Starter: Pat Germain

    I've been away from woodworking for about ten years while I was restoring a car. It was something wanted to do since I was a kid and I finally got it done. Now I want to get back into woodworking and I will need a new table saw. I had been using a hot-rodded Craftsman contractor saw. It got the...

    Last Post By: Leigh Betsch Yesterday, 3:19 PM Go to last post
    Thomas Colson

    How to replace Syder/Coupler on Supermax 16/32>?

    Thread Starter: Thomas Colson

    I have a Supermax 16/32 with a pretty clapped out rubber spyder-coupler. Little tiny pieces of rubber are coming out of it, which makes sense, I've used this like I stole it for the last 2 years. Any videos or instructions with pictures anywhere on how to do this that are deliberately hidden and...

    Last Post By: Ronald Blue Yesterday, 2:51 PM Go to last post
    Brian Elfert

    I think my zero turn mower is cursed!

    Thread Starter: Brian Elfert

    I bought a used 2019 Grasshopper diesel zero turn mower with 189 hours on it last summer. I had all kinds of problems with it initially including a starter that didn't always turn over. I realized after I bought it that the mower had been buried pretty deep in mud or something as the dashboard...

    Last Post By: Michael Schuch Today, 2:35 AM Go to last post
  • Ben Rivel

    There is no available content written by Ben Rivel
  • Recent Polls

  • Recent Forum Posts

    Chris Parks

    Yet another Dust collecting topic

    A 17.7 inch impeller will do anything you want and will support 3 x 150mm blast gates being open at the same time. We always use 225mm pipe for a main

    Chris Parks Today, 8:39 AM Go to last post
    Mike King

    new bandsaw wont' cut straight

    The blade is new and while there may be other blades that are superior, I find it hard to believe that the issue is your blade. Rather, it is far more

    Mike King Today, 8:37 AM Go to last post
    mike calabrese

    Maple & epoxy segmented bowl

    Hi Sam,
    No there was no mold release considered. The intent was to cut away the "pine box" that was the mold . I simply ran the segments

    mike calabrese Today, 8:33 AM Go to last post
    Ronald Blue

    Harvey Slider on Unisaw?

    I have the Excalibur slider and it will take a full sheet as it sits. Crosscutting longer boards or something wide that would be a real challenge otherwise

    Ronald Blue Today, 8:30 AM Go to last post
    mike calabrese

    Maple & epoxy segmented bowl

    Hi David,
    Thanks for looking in and thanks for the review. I often get caught up in the process more than the result and what you see is what I

    mike calabrese Today, 8:28 AM Go to last post
  • Recent Blog Posts