• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Michael Arruda

    Home Depot return policy change without notification

    Thread Starter: Michael Arruda

    Hello all, I had some small items left over from various things I've done around the house recently and decided to gather them up to take back to Home Depot. These items were purchased at various times over the past couple weeks and I of course misplaced my receipts. Meaning they got washed,...

    Last Post By: william watts Today, 1:48 PM Go to last post
    Tim M Tuttle

    Jointer Safety

    Thread Starter: Tim M Tuttle

    I've been milling up a lot of white oak the past two nights. While I was using my jointer I started to ponder safety. For something like the table saw there are a lot of common safety procedures/dos/donts. A lot more than a jointer which makes sense as there are a lot more variables with the...

    Last Post By: Mel Fulks Today, 1:32 PM Go to last post
    Tom Trees

    Suitable relay for three wire control on a VFD

    Thread Starter: Tom Trees

    Hello folks I have been walking through the steps with another forum member on setting up a VFD for his saw. Unfortunately the VFD does not have a relay OR COMMON for three wire control/push button station. Can any of you guys point me in the right direction to find a suitable relay for him? ...

    Last Post By: Tom Trees Yesterday, 2:31 PM Go to last post
    Ronald Blue

    Two Year Old Camaster Stinger III

    Thread Starter: Ronald Blue

    I have a locally available Camaster Stinger III. It's a 4 X 8 machine with a three head setup. Whats the benefit of the three head arrangement? Is it an alternative to an ATC system? What's a fair price? He says it was $18,000 new. He's discounted it a lot from that amount. Nearly half. He did say...

    Last Post By: Jim Becker Today, 9:38 AM Go to last post
    John Sincerbeaux

    Vacuum Fence for Slider

    Thread Starter: John Sincerbeaux

    Finally finished my vacuum tall fence for my slider. Made of commercially available parts from companies in the CNC industry. Aluminum T-slot plate 16 x 24 4) 4 x 4 aluminum pods pneumatic switch powered by vacuum pump from Vacuum clamping systems. The objectives for this fence were...

    Last Post By: John Sincerbeaux Today, 12:00 PM Go to last post
    Steve Rozmiarek

    Good quality mobility bases?

    Thread Starter: Steve Rozmiarek

    Anyone have recommendations on decent quality and reasonably priced mobility bases for table saws? I haven't paid any attention to the market in years, googled yesterday and was a little shocked at the prices I saw. Last I remember, they were half of what I'm seeing now. Bases for would cost...

    Last Post By: Rod Sheridan Today, 8:35 AM Go to last post
  • Bill Carey

    There is no available content written by Bill Carey
  • Recent Polls

  • Recent Forum Posts

    Jim Koepke

    Now what? Socketed chisel handle removal

    Roger, you are correct in what you have said. Unfortunately not all users of socket chisels have exercised your degree of tool care and maintenance. Fitting

    Jim Koepke Today, 2:23 PM Go to last post
    Jim Koepke

    Stanley No. 45 Parts

    My knowledge of Martin J. Donnelly's business practices is zilch.

    The threaded rods for the Stanley #45 were only used from 1884-1896.

    Jim Koepke Today, 2:07 PM Go to last post
    Brice Rogers

    Walnut oil

    I attended a seminar by Mike Mahoney who sells his own brand of walnut oil and was told that he (essentially) boils it which changes it to make it polymerize

    Brice Rogers Today, 2:03 PM Go to last post
    Bill Dufour

    garage roof with no rafter or collar ties.

    Just saw pictures online looked like about 4x14. All rafters had simpson clips top and bottom. I would guess not more then 24 feet long. It looked

    Bill Dufour Today, 2:03 PM Go to last post
    Simon Dupay

    Turned my hands purple?

    Lemon juice will remove most of the purple. Although if you have any cuts on your hand....

    Simon Dupay Today, 1:56 PM Go to last post
  • Recent Blog Posts