Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Mike King Yesterday, 3:50 PM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: Troy Gamm Yesterday, 7:09 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: Brian Runau Yesterday, 1:07 PM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Warren Lake Yesterday, 8:56 PM

Freud hand held router FT2200VCE bit is moving
Thread Starter: Brian Runau
I use this to do hand work and it has worked fine over the years. I have it set right now to do some template work and it is/was set for 5/16" depth. Bit seems to be tight in the collect and the locking lever is/was tight. This morning as I was routing 16 spots on night stand legs to let in a...
Last Post By: Jim McLeod Today, 5:45 AM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 6:05 PM

greg king

There is no available content written by greg king

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Swiss Army ... tool

Maybe it should be a requirement for the Exit row--so the passenger could torque the door bolts before take-off.
Earl McLain Today, 6:56 AM

Sandblasting

I want to accentuate the texture of the grain by removing some of the summer wood.
What methods have people used for doing this?
If sandblasting,what
STUART Robertson Today, 6:27 AM

Freud hand held router FT2200VCE bit is moving

I know this is an old post but can't seem to reach anyone at Derosa by email or phone. Will the type 2 fit a Freud FT2000E? Not sure if there is any shaft
Jim McLeod Today, 5:45 AM

What paint for a new exterior fiberglass door?

Go to a paint store and ask for a recommendation, someplace like Sherwin-Williams, or PPG. Expect to spend $75-100/gallon, or $30-40/quart for a quality
Jason Roehl Today, 5:12 AM

Glue Chairs

The only glue that will strike through old glue is hide. If PVA was originally used, injecting it into a partially closed joint isn't going to do much
Charles Edward Today, 3:37 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

greg king

Recent Polls

Recent Forum Posts

Recent Blog Posts