Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Shop Build...should be a fun journey...
Thread Starter: Jim Becker
I debated about starting this thread now or later, but decided on now because, well...I might forget something. :o As a little background, at our previous property, I was blessed with a reasonably sized, fully conditioned space for my shop in what was originally a three-and-a-half vehicle garage...
Last Post By: glenn bradley Yesterday, 9:45 AM

Dust Collector recommendations
Thread Starter: Michael Rutman
Oh boy, reading the archives I can see this is not a simple question, which makes me feel good because I am completely lost. I have never owned a dust collector mostly due to inability to figure out what I need, and that needs to change. So, let me go over my shop, my needs, and then beg for...
Last Post By: Mark Klika Today, 7:47 AM

VFD for 7.5 hp 3 phase to run on 220 single phase
Thread Starter: Mike Leiferman
Anyone with any experience running a 7.5 hp 220 volt 26 amp 3 phase from a VFD powered by 220 single phase? I would like to know a) what specific vfd you are using if you recommend it, b) any issues I should be aware of The motor is driving a 1995 Lazzari Tema 3000i. The alternative for me...
Last Post By: Jared Sankovich Yesterday, 10:04 AM

Cost effectiveness of a slider vs. tracksaw & tablesaw
Thread Starter: Jonathan Jung
I thought about posting this to the business section, because I'd really like input from professionals who use their shop as a business. For those of you who make $ or even a living making furniture or cabinets, how long does it take for a sliding table saw to pay for itself compared to a track saw...
Last Post By: Kevin Jenness Yesterday, 9:49 AM

Anyone have experience with Sheds Unlimited?
Thread Starter: Roger Feeley
We are looking into building a 3 car garage with living space above. https://shedsunlimited.net/garages/legacy-workshop-three-car-garage/ These folks will manufacture modules and erect the shell. Then it’s up to us to finish it.
Last Post By: Brian Elfert Yesterday, 9:44 PM

Return Air Baffle for CV1800
Thread Starter: Bryan Cleveland
I’ve been designing a closet for my CV1800 for a few months trying to find a way to make it fit in my little garage and I think I have finally cracked it. My only concern is with the return air baffle I designed. Garage is air conditioned so return air is a must. I’ve read so many posts about...
Last Post By: Malcolm McLeod Today, 7:32 AM

Phil Mueller

There is no available content written by Phil Mueller

Recent Polls
Recent Forum Posts

Miter Saw Vertical Cuts not Square

Your only options are to; 1.) have a machine shop machine your hinge pivot casting and blade spindle casting parallel. Or 2.) Order an OMGA and be done
Bobby Robbinett Today, 8:02 AM

Options for Harvey Table Saw?

I think most folks will tell you 3hsp. That has been the standard for years and years. For 35 yrs or so I used a delta contractor and made aliving with
Michelle Rich Today, 7:55 AM

Dust Collector recommendations

It certainly does help, Luis! Thank you for the reply! Mark
Mark Klika Today, 7:47 AM

3-Phase vs Single Phase Equipment

Are you sure the 54A rating on the wide-belt sander is 3-phase? And at what voltage? At 208V, that’s a 20hp motor.
Jason Roehl Today, 7:36 AM

Return Air Baffle for CV1800

Continuing the hijack, just a little... Slab on grade with post-tension cables (PTCs) is essentially the standard in N.TX, and has been for 30-40yrs
Malcolm McLeod Today, 7:32 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Phil Mueller

Recent Polls

Recent Forum Posts

Recent Blog Posts