Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Jim Allen Yesterday, 5:25 PM

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Alan Lightstone Today, 1:01 PM

California bans gas lawn mowers and leaf blowers after 2024
Thread Starter: Bill Dufour
Saw a sign at hoe despot and looked it up. California has banned the sale of gas lawnmowers and leaf blowers after 2024. If yours is getting tired better buy a new one in a few months. I assume they will be gone from stores by Fall. It will probably take ten to twenty years until this ban goes...
Last Post By: Doug Garson Today, 12:55 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: steven c newman Yesterday, 8:20 PM

Residential fence rules
Thread Starter: Stan Calow
I am looking for what people in other jurisdictions have dealt with. I have always understood that, in my city, fences between homes were the responsibility of the homeowner who first puts it up. And the rule was "good side out" and 6" off the property line. But after a discussion with a...
Last Post By: Warren Lake Today, 12:46 PM

Seeking Recommendation on a Bench Grinder with Specific Features.
Thread Starter: Scott Memmer
Hi, Everyone. I dearly love this forum, although I have not posted in a long time. You folks are so knowledgeable and always have such great suggestions. Here is my situation. I make a small music accessory and need to build my own saw. Without going into all the details, I've been searching for...
Last Post By: Ray Selinger Today, 11:51 AM

Russell Stanton

There is no available content written by Russell Stanton

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Need a New Resaw Blade

Good points. I was responding to the inference that sharp is the only thing that matters ("sharp is what matters"). I'm fortunate to have
Cameron Wood Today, 2:22 PM

Left lane

Here is the law in BC. This applies to B.C. highways with two or more lanes of traffic travelling in the same direction and a posted speed limit of 80
Doug Garson Today, 1:56 PM

Left lane

They wouldn't last long on the Autobahn in Germany.
Doug Garson Today, 1:52 PM

Left lane

I've seen worse, people drive to the end of the merge lane and stop waiting for a break in traffic to pull out. Not seen it often, perhaps those they
Doug Garson Today, 1:45 PM

Laguna Dust Collector not going on

Is that box just a junction box? Could you have only fried a terminal because of a loose connection?

If the motor is fried and caused the
Robert Hayward Today, 1:44 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Russell Stanton

Recent Polls

Recent Forum Posts

Recent Blog Posts