• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Mike Heidrick

    Pole Barn 40X64X16

    Thread Starter: Mike Heidrick

    Signed a contract yesterday with S&L Builders out of Indiana for a 40X64X16 Pole Barn with a 10X24 porch. Build date August 18, 2014. Plan to install Pex for raidant floor heat. Concrete slab 5" thick. Also doing 1.5" closed cell foam under the pad. Built on Laminated posts in ground. Will...

    Last Post By: Mike Heidrick Today, 3:24 PM Go to last post
    dennis thompson

    Stocks and "the market"

    Thread Starter: dennis thompson

    Why do people keep predicting what " the market" will do for the next year. I would bet that none of these market predictions for 2019 was for a 30% gain , yet this week Barrons has their annual roundtable in which market experts make their predictions for 2020, why? The only good answer to the...

    Last Post By: Doug Dawson Today, 3:42 PM Go to last post
    Bill Jobe

    Did you get a flu shot?

    Thread Starter: Bill Jobe

    So did I. A couple of months ago. I am just recovering from the flu that totally disabled me for the last week, after another week of just not feeling up to snuff.

    Last Post By: Greg Funk Today, 4:34 PM Go to last post
    Patrick Walsh

    1982 Martin T-23

    Thread Starter: Patrick Walsh

    And so it seems it begins again. The T-75 isn’t even technically done and I have a new project. I’m not gonna go all buggy on this one “just yet” if ever. I will 100% go all the way through the machine and make sure it is 100% fully functional to the 9’s. 10’ for me if it was a term. If anything...

    Last Post By: Jeff Duncan Today, 2:43 PM Go to last post
    Travis Conner

    Is there money in woodworking?

    Thread Starter: Travis Conner

    Other than making kitchen cabinets, is there money in it? I've always kept it as a hobby. I once heard of a guy who won the lottery say he's going to keep wood working until the money runs out. Lol

    Last Post By: Doug Dawson Today, 4:08 PM Go to last post
    Mike Randall

    Work Bench Top Material

    Thread Starter: Mike Randall

    I'm in the process of designing and building my first woodworking work bench and I'm looking for some opinions. I plan on using a two layer top with 3/4" plywood as the base and the top layer either another piece of 3/4" plywood or 3/4" MDF. Any thoughts on pros and cons? -Mike

    Last Post By: Jon Nuckles Today, 11:48 AM Go to last post
  • Brian K. Harris

    There is no available content written by Brian K. Harris
  • Recent Polls

    What's your opinion? (Votes: 20)

    1. It's a shame, that could have been some really nice wide panels. (Votes: 17)

    2. Yesssssss, the world can never have enough heavily checked cookie tables. (Votes: 3)

  • Recent Forum Posts

    Richard Coers

    Hollowing Systems

    I McGivered my whole system. Articulated system inspired by the Kobra, camera system is a $10 inspection camera off eBay on an ancient laptop. Maybe $50

    Richard Coers Today, 4:52 PM Go to last post
    Paul F Franklin

    Need some design help with a desk

    If I follow what I think you asking about, search for cockbeading a drawer. That's the process of wrapping a flat drawer front with beaded molding.

    Paul F Franklin Today, 4:45 PM Go to last post
    Richard Coers

    Is a 12" jointer needed?

    If you only do a couple wide boards for a project, and you are a hobbyist, you can make a sled and flatten stock on a bench top planer. If you will run

    Richard Coers Today, 4:39 PM Go to last post
    Ken Platt

    can you flatten a 1/4 inch thick piece?

    Folks - I have a small piece of red oak that is wildly figured, that I'd like to use for veneering onto another piece in order to use it for a drawer

    Ken Platt Today, 4:37 PM Go to last post
    John TenEyck

    Em6600 by target

    Target shows a 1.8 mm N/N set, or larger. The viscosity works out to be about 100 seconds #4 Ford cup for EM6600. I could spray it with a 1.3 or 1.5

    John TenEyck Today, 4:34 PM Go to last post
  • Recent Blog Posts