Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Time for some levity
Thread Starter: Dave Anderson NH
With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.
Last Post By: Kev Williams Today, 5:43 PM

Paint booth fan?
Thread Starter: Leigh Betsch
I am converting my downdraft sanding table to a duel purpose downdraft/paint booth. Basically I have a 3'x5' downdraft bench on wheels with an old furnace blower to draw the sanding dust thru the table and out thru furnace filters. With my sander hooked to my Festool dust extractor, it does a...
Last Post By: Leigh Betsch Yesterday, 8:04 PM

Help Me Pick a Plow Plane or Is It a Plough Plane
Thread Starter: Thomas McCurnin
Typical use will be on 3/4 to 7/8" stock planing on edge for a a 1/4" groove about 3/8" deep for frame and panel construction. I'll also be using it for grooving a post, usually about 1.5" x 1.5" is typical, again to accept a panel for frame and panel construction. It needs to go both directions,...
Last Post By: Derek Cohen Today, 1:55 AM

Build a Shaker Style Table Project
Thread Starter: steven c newman
Had those planks of Ash....four at 7/8" x 5-1/2" x 77" and one at 7/8" x 5-1/2" x 48"......and figured I could try to build a Shaker Style Table, complete with a drawer....I remember way back when, during the New Yankee Workshop days, that Norm built such a table. Have to go strictly by memory,...
Last Post By: John Kananis Today, 12:52 AM

Restoring a de Havilland Mosquito
Thread Starter: Kris Cook
There is a pretty neat article in the Jan/Feb issue of Popular Mechanics about restoring a Mosquito. For those unfamiliar with this airplane it was constructed almost entirely from wood. Fuselage was a 5/8" thick sandwich of plywood and balsa!! That, combined with two RR Merlins made it a...
Last Post By: Maurice Mcmurry Today, 9:08 AM

Solid Walnut bookshelf dados - is glue enough?
Thread Starter: Bill Brammer
Building 6 ft high, 28 in wide, 12 inch deep solid 3/4 inch walnut bookshelf , no adjustable shelves. I have dados for all shelves. The sides are a little bowed, requiring some pressure with clamps to pull them together with the dados. Not a ton, but some. I'm trying to decide if I need to add...
Last Post By: Derek Meyer Today, 6:39 PM

Curt Harms

There is no available content written by Curt Harms

Recent Polls
Recent Forum Posts

Water leaking under slab

Seems like a hot water line under a slab is a failure waiting to happen, 'expansion' ...
Tom Bender Today, 6:43 PM

Solid Walnut bookshelf dados - is glue enough?

You could try the Norm Abrams method, where he sets the shelf in a dado and then uses a pin nailer to shoot nails through the shelf and into the side.
Derek Meyer Today, 6:39 PM

Does A Blowers CFM Rating Change When Converting to A Cyclone Setup?

Correct . Find the machine that may have what your looking for , click on " buy parts " . That particular impeller is the one that can be found
james manutes Today, 6:32 PM

Powermatic 180 planer, tie down to a trailer

Went pretty well. Now I have to figure out if the gears are all working. The adjustable bed rollers do not lift. Seem to be stuck. The stuff under
Bill Dufour Today, 6:26 PM

How to replace Syder/Coupler on Supermax 16/32>?

https://flic.kr/p/2nmsPY6
https://flic.kr/p/2nmjZLA
https://flic.kr/p/2nmqir9
https://flic.kr/p/2nmjZP1
https://flic.kr/p/2nmjZQ8
Thomas Colson Today, 6:21 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Curt Harms

Recent Polls

Recent Forum Posts

Recent Blog Posts