Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Kevin Jenness Today, 8:15 AM

Cheap Bandsaw for Resawing
Thread Starter: Jimmy Harris
I'm a hobbyist on a limited budget looking for a bandsaw, primarily for resawing. Let's say, 12" of 8/4 hard maple cut down the middle would be the maximum I would ever ask of it. I'm under the impression that I'll need a steel framed bandsaw for that. What else do I need to know? Are guides...
Last Post By: John Kananis Yesterday, 3:13 PM

Are they building standalone car washes like crazy in your area too?
Thread Starter: Brian Elfert
They are going crazy building standalone car washes in my area. I know of at least three currently under construction nearby, and a few others that recently opened. Car washes are going up all over the Minneapolis metro area. There will easily be three times as many standalone car washes once...
Last Post By: Brian Elfert Yesterday, 4:24 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: Brian Runau Today, 8:55 AM

LLAMBRICH Intergrated arbor and chuck
Thread Starter: Patty Hann
Opinions, please on integrated arbor and chuck for a DP. Am looking at the LLAMBRICH Keyless chucks ... integrated 2MT shank/arbor 1/32" to 3/8" (part# JK10-MT2) 1/32" to 1/2" (JK13-MT2) Thanks
Last Post By: Bill Dufour Today, 12:23 AM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Jerry Bruette Yesterday, 11:40 PM

TYLER WOOD

There is no available content written by TYLER WOOD

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Record player table

Thats very clever and striking! A very good job. Having that in the room will be an excellent reminder to stop and put on an album.
Maurice Mcmurry Today, 8:56 AM

Gable Vent

The old house in the picture needed some but never had any. Every roof peak was a different angle and each side was a little different. I just figured
Tom M King Today, 8:56 AM

landscaping is my other hobby, record for me, 25 yards of mulch

Julian, I use a spring pre-emergent with low nitrogen, say @ 18. I try to minimize how much nitrogen I add in the spring since it just makes me have to
Brian Runau Today, 8:55 AM

Outdoor White Oak

It matters a lot where you live, and where the piece will set.

Sitting in the shade where mold is prevalent is problematic for any material.
Carl Beckett Today, 8:52 AM

Gable Vent

The drawing shown on the first page of this site should be all the plans needed, but the prices look pretty hard to match for DIY unless time is worth
Tom M King Today, 8:43 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

TYLER WOOD

Recent Polls

Recent Forum Posts

Recent Blog Posts