• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Patrick Walsh

    Vintage Martin T75 restoration

    Thread Starter: Patrick Walsh

    So I have a opportunity to purchase the above machine for a fair deal from my employer. I am aware of the phenolic guides being pop riveted I the the sliding table along with not availible for replacement. So my question is as follows to those in the know with regard to the phenolic ways....

    Last Post By: Jim Becker Today, 1:10 PM Go to last post
    Dan Friedrichs

    "Professional" paint (Sherwin Williams, etc) vs Box-Store paint

    Thread Starter: Dan Friedrichs

    In our new house, I bought Valspar Signature paint from Lowe's to paint the entire interior, but ended up hiring professional painters to do the job. Nice, honest guys, who very timidly pulled me aside after putting on 2 coats of the Valspar and asked if I'd be offended if they went and bought...

    Last Post By: lowell holmes Today, 12:38 PM Go to last post
    Bennie Dempsey

    3D Planning Software

    Thread Starter: Bennie Dempsey

    Hey all! I would like to start planning out my projects before I begin them, as I've heard that's a good habit to have. I can find a modeling program online pretty easily, but I wanted to see what you guys use. I am awful at hand drafting so paper and pencil isn't my go-to for personal projects....

    Last Post By: richard b miller Today, 11:05 AM Go to last post
    Larry Frank

    Dust Bin Sensor Completed

    Thread Starter: Larry Frank

    After reading all of the fine work by several members, I decided that I wanted to add the dust bin sensor to my Oneida Super Dust Gorilla. I ordered most of the parts on eBay. The sensor was $3.79, the delay relay board was $4.95 and the 12 V power supply was $9.99. I used some LED trailer...

    Last Post By: Bob Hinden Yesterday, 7:37 PM Go to last post
    Dave Lehnert

    New Zero Turn Mower

    Thread Starter: Dave Lehnert

    Starting to think about a new Zero Turn Mower. I now own a Toro 52" with a 19 Hp Kawasaki that I have been happy with. Mow 2 1/2 acr all flat. What brand have you been happy with? More important. Is there a brand you have had trouble with? Parts hard to get etc.....

    Last Post By: Ronald Blue Today, 12:50 PM Go to last post
    Greg Parrish

    Folding Table - Which One?

    Thread Starter: Greg Parrish

    Looking for some feedback and input on folding tables like the Festool MFT and Kreg Adaptive System. I would be using this for occasional cuts using my Makita track saw, but on a more regular basis as my sanding surface for my Festool sander/vac and as an assembly/clamping table. i need easy fold...

    Last Post By: ChrisA Edwards Yesterday, 6:14 PM Go to last post
  • roger wiegand

    There is no available content written by roger wiegand
  • Recent Polls

    What color do you pick? (Votes: 72)

    1. Black (Votes: 16)

    2. Blue (Votes: 9)

    3. Green (Votes: 4)

    4. Orange (Votes: 3)

    5. Red (Votes: 27)

    6. Yellow (Votes: 3)

    7. White (Votes: 3)

    8. Other (Votes: 7)

  • Recent Forum Posts

    Jim Dwight

    Full kerf blades on 40's 1.5 hp unisaw

    I will agree with the other opinions. I've owned at least 5 table saws and all were 110V. My current main saw is a PCS with the 1.75hp motor. I've

    Jim Dwight Today, 1:16 PM Go to last post
    Dave Burson

    Rust prevention

    How about if the TS top already has some rust spots on it? Best way to get it out, and smooth, prior to doing the Johnson's wax treatment? I know about

    Dave Burson Today, 1:15 PM Go to last post
    Frederick Skelly

    Northeast alabama

    Rich,
    I know there are at least 2 creekers in huntsville, but on the map that looks more north-central than northheast. So i dont know if it helps.

    Frederick Skelly Today, 1:14 PM Go to last post
    Dave Burson

    dual tablesaw setup?

    3 saws? Hmmmm... I like it. I especially like the idea of combining all that into one station maybe. I'm thinking a router table on the right side of

    Dave Burson Today, 1:11 PM Go to last post
    Rob Luter

    Henry Taylor gouges?

    About to pull the trigger (busy summer) but doing a little more research prior to heading down the rabbit hole. I’ll be making spoons and small

    Rob Luter Today, 1:11 PM Go to last post
  • Recent Blog Posts