Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

Spindle gouge bevel angle?
Thread Starter: John Kananis
I have a 1/2" sorby detail gouge that I have ground at 40° (also removed the heel) and it works ok now that I moved away from the jigs and started sharpening by hand... but it's still just an ok tool. I now have a d-way detail spindle gouge (1/2") on the way and was thinking about trying a 25°...
Last Post By: John Kananis Yesterday, 2:16 PM

Harvey Slider on Unisaw?
Thread Starter: John Kananis
All these slider threads got me thinking. Does anyone here have the Harvey compass st-1500 attached to their unisaw? Can you speak on the quality, ease of attachment, capabilities and shortcomings? Thank you in advance!
Last Post By: Troy Gamm Yesterday, 2:51 PM

Need ideas on waterproof board to cover water damaged base of outside doors
Thread Starter: Randall J Cox
I have two exterior doors, one to the back of my house and one to my tool shed. Both are showing the effects of winter water splashing up on them at the base. The door to my shed is really bad. I don't want to replace the doors but would like to put a board over the base, like a kickplate to...
Last Post By: Stan Calow Today, 9:20 AM

Hot water sulfur smell solutions
Thread Starter: Ron Citerone
My cottage is on well water. Several years ago we started with the dreaded sulfur smell, hot water only. I had a plumber replace the anode. Smell came back eventually. I found the model of the anode he installed and see that is just aluminum. Seems like the one I need is aluminum/zinc? Has...
Last Post By: Ron Citerone Today, 8:46 AM

Vectric Software V12 Now Available
Thread Starter: Michael Burnside
I was talking with friend over the weekend and they were unaware that V12 has been released. So, I figured I would post here in case someone wasn't aware of this news. In general the upgrades look good overall. I personally upgraded my version of Vcarve Pro.
Last Post By: Jim Becker Today, 8:31 AM

Issues dealing with Wiktor Kuc of WKtools.com
Thread Starter: Bob Betker
I am not sure if this is the correct forum for this post but since it is hand-tool related I thought it appropriate. I ordered a couple of items from Wiktor Kuc of wktools.com about 16 months ago and I’m trying to get some advice on how to proceed. Here is a summary of what has transpired. ...
Last Post By: Tony Zaffuto Yesterday, 2:41 PM

Monty Opsal

There is no available content written by Monty Opsal

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

Hedge trimmer cleaner

After thinking about it, my long handled Stihl was new in 1999 and I've never cleaned it that I remember. I do remember sharpening it a couple of times.
Tom M King Today, 9:24 AM

Need ideas on waterproof board to cover water damaged base of outside doors

How about a clear waterproofing, like Flex Seal?
Stan Calow Today, 9:20 AM

Charcuterie Board Handle

I've used drawer pull hardware for this, either basic or fancy. But agree it makes it harder to store. The routed slots are good too.
Stan Calow Today, 9:17 AM

LLAMBRICH Intergrated arbor and chuck

I find this idea very interesting, especially the one piece version for simplicity and presumably reduced risk of runout. I just have to somehow get past
Jim Becker Today, 9:03 AM

Systainers?

This is totally a subjective thing, Tom, both for personal preferences around organization as well as functionally how we use our tools. So you are not
Jim Becker Today, 8:57 AM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

Monty Opsal

Recent Polls

Recent Forum Posts

Recent Blog Posts