• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Patrick Walsh

    Vintage Martin T75 restoration

    Thread Starter: Patrick Walsh

    So I have a opportunity to purchase the above machine for a fair deal from my employer. I am aware of the phenolic guides being pop riveted I the the sliding table along with not availible for replacement. So my question is as follows to those in the know with regard to the phenolic ways....

    Last Post By: Brian Holcombe Today, 2:39 PM Go to last post
    Alan Heffernan

    Which Slider Miter Saw to buy?

    Thread Starter: Alan Heffernan

    My son is starting a shop from scratch and looking for the best miter/slider saw to buy. Best = accurate, repeatable, reasonable cross cut capacity, dust collection, and reliable. (Edit: added dust collection) He has just bought a new house with a full basement and will be building out his...

    Last Post By: Alan Heffernan Yesterday, 10:39 PM Go to last post
    Jon Snider

    New shop build, the MBS

    Thread Starter: Jon Snider

    I’ve received some offline encouragement to post some content of my new shop build. If you’ve read any of my other numerous questions (thx all for invaluable help), I’ve been at this since last April. Here is an effort to slowly catch up. The shop replaces the same spot where I built a veggie...

    Last Post By: Jon Snider Today, 11:46 AM Go to last post
    Scott Winners

    About sharpening handsaws

    Thread Starter: Scott Winners

    There is some agitation in another area here to opening a sub forum specific to sharpening. I am far too new to have a valued opinion on the subject, though I am in favor. I can generally apply a rule of thirds when I take up a new thing. For joinery, sharpening saws turns out to be easy for...

    Last Post By: Bruce Haugen Today, 6:36 PM Go to last post
    Andrew More

    What are the actual rates of serious accident in the woodshop?

    Thread Starter: Andrew More

    So I've been thinking about getting a SawStop for a while. Not going to happen just yet, mostly because of budget. The safety aspects are clear, and nobody wants to have a table saw accident. However, what about the other tools in the shop? Having a saw stop doesn't help me much if I mess up...

    Last Post By: John Kee Today, 11:25 AM Go to last post
    Karl Card

    table saw tuning......

    Thread Starter: Karl Card

    Curious as to what number is considered very good in a table saw setup. My blade is just about dead on as far as the blade to the miter slot but miter slot to fence is about .003 off. I mean that the end of the fence on the back side of table saw is .003 away from blade than the front part of the...

    Last Post By: David Kumm Today, 6:24 PM Go to last post
  • Aaron Koehl

    by Published on 02-27-2011 5:33 PM     Number of Views: 15641 

    Do you have woodworking knowledge you're just dying to share?
    Want to be an author at Sawmill Creek?

    Now you have a new area to publish articles!

    If you want to publish an article, you can join our authors group, which gives you access to a forum which is open only to would-be authors at SawmillCreek. This is a staging area for new articles, where you can post a new article, and we'll review for publication. Once you're ready to publish it, we'll promote it on the front page of SawmillCreek!


    The process is simple:

    1. Join the Authors group by visiting this page.
    2. Once you have access, visit the Authors forum.
    3. Start your article by creating a new thread in that forum.


    TIPS

    If your article is too long for a single post, don't fret ! Spread your article over multiple posts, and we'll merge them together into a single post when the article is ready to be published.

    Try posting pictures inline for visual interest.

    Choose a catchy, yet descriptive title!

    Writer's Block?

    We're looking for tool reviews, woodworking tips, woodturning techniques, jigs and fixtures, finished projects step-by-step, finishing techniques, social woodworking experiences, and even good compilations of our existing thread topics.

    Good luck and Happy writing!
    _Aaron Koehl_
    Published on 01-05-2011 7:24 PM     Number of Views: 27262 
    Article Preview

    An article on segmented bowls by one of our original moderators, Ken Salisbury.

    This article describes the process used to make the following bowl.

    ...
    Published on 01-02-2011 5:43 PM     Number of Views: 5062 

    Jack Explores the excitement and some of the challenges he faced when
    introducing children to woodworking.
    ...