• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    brent stanley

    A Timberframed Woodworking Shop - Build Thread

    Thread Starter: brent stanley

    This weekend I started working on what will be my new workshop. A 25x40 timberframe and plan on documenting it fairly thoroughly. If folks are interested, please let me know and I'd be happy to spend some time documenting it for folks here. Cheers, Brent

    Last Post By: brent stanley Today, 12:01 PM Go to last post
    Roger Benton

    clifton vs lie nielsen????

    Thread Starter: Roger Benton

    Been wanting a #4-1/2 for a while and decided to save up the cash and buy new. I'd love to hear from any owners of Clifton planes, as that is LN's only competition for my $$$. I'd set it up and use it only for fine smoothing, to complement my #3. So let's hear some opinions from the Clifton folks!

    Last Post By: Steven Herbin Today, 8:32 AM Go to last post
    ken hatch

    New Moravian Bench build Part 2

    Thread Starter: ken hatch

    The old thread was getting a little long in tooth. Friday night I screwed up one of the long stretcher tenons. After several rounds of "what if" and "yes but" I made the correct decision and went to the woodstore Saturday and picked up a nice hunk of 12/4 Poplar and started over. Here are...

    Last Post By: ken hatch Today, 6:25 PM Go to last post
    Rick Potter

    I just did the unthinkable.

    Thread Starter: Rick Potter

    Tool junkie heresy. I am getting ready to add a new garage for my old cars, and I have been storing too many tools. Today, I hauled a perfectly good 12" Rockwell single phase 110/220 turret RAS to Goodwill. I just didn't want to fool with selling it. I sure picked a lousy day to do it. ...

    Last Post By: Ben Helmich Yesterday, 9:38 PM Go to last post
    Tom Bender

    Caffeine - Rollercoaster into Hell

    Thread Starter: Tom Bender

    Caffeine and other stimulants I have tried provide a nice boost but it's a rollercoaster that goes a little less high and decends a little lower with each cycle.

    Last Post By: Jim Koepke Today, 2:00 PM Go to last post
    Edwin Santos

    Jorgensen clamps at Lowes

    Thread Starter: Edwin Santos

    Hi, I don't quite know what the story is with the orange Jorgensen bar clamps. At one point I heard the century old company went out of business. Then I heard a Chinese company bought them and planned to resurrect the line. Today I saw a six pack of 6" 3700 series bar clamps at Lowes. They're in...

    Last Post By: Paul F Franklin Yesterday, 7:12 PM Go to last post
  • Thomas Wilson

    There is no available content written by Thomas Wilson
  • Recent Polls

    What color do you pick? (Votes: 71)

    1. Black (Votes: 16)

    2. Blue (Votes: 9)

    3. Green (Votes: 4)

    4. Orange (Votes: 3)

    5. Red (Votes: 27)

    6. Yellow (Votes: 3)

    7. White (Votes: 3)

    8. Other (Votes: 6)

  • Recent Forum Posts

    Matt Day

    Amazon mini-rant

    If you read the emails, they’ve done their job.

    Matt Day Today, 6:31 PM Go to last post
    Barry McFadden

    Amazon mini-rant

    I love it when I am searching for a present for my wife and the next time either one of us uses the computer there are adds all over the place for that

    Barry McFadden Today, 6:29 PM Go to last post
    ken hatch

    New Moravian Bench build Part 2

    The first fitting of the slab to the base is not too bad, the backer board needs a bit of trimming, maybe a mm or two off where the angle meets the forward

    ken hatch Today, 6:25 PM Go to last post
    Andrew Hughes

    Best reason ever for owning a bandsaw

    I’m the same way when it come to my machines. I admit some of my reasons are superstitious.
    My most coveted machine surface is my jointer.

    Andrew Hughes Today, 6:20 PM Go to last post
    Scott Holmes

    Spar Varnish

    What is your project? Interior use an interior finish; exterior use a spar/marine outdoor finish.

    Scott Holmes Today, 6:14 PM Go to last post
  • Recent Blog Posts