• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Jerome Stanek

    Glowforge release

    Thread Starter: Jerome Stanek

    I was wondering if Glowforge has sent out any units yet. I thought they were supposed to release the middle of December.

    Last Post By: Bert Kemp Today, 11:17 PM Go to last post
    Ryan Pappas

    Hammer slider vs. Minimax

    Thread Starter: Ryan Pappas

    I have decided to sell my sawstop and get a sliding table saw. I have narrowed it down to hammer k3 79x48 and minimax. I have the SC2 and the SC4 in mind for minimax. Also adding in the SC3 to the mix. I mainly make end grain cutting boards so not sure if a full 8ft is necessary for me but I know...

    Last Post By: Peter Kelly Today, 10:22 PM Go to last post
    John C Cox

    Show me your chisel racks

    Thread Starter: John C Cox

    Hey guys, I need to make a bench top or wall mounted chisel rack and need some ideas... What is your favorite one you have made? Pix please. :D :D Also - do you do anything differently for socket chisels vs tang chisels. I would hate to find the beautiful socket chisel irons all...

    Last Post By: Nicholas Lawrence Today, 10:30 AM Go to last post
    Ray Newman

    Waterstones

    Thread Starter: Ray Newman

    Colleagues: need some recommendations as to a water stone set. Am tired of the Tormek required pre soaking time before use. As a result, I put off sharpening or touching up the edge until it is really dull. Last time I was at the local tool emporium, clerk raved about the Shapton glass backed...

    Last Post By: Chet R Parks Today, 12:14 PM Go to last post
    Brandon SPEAKS

    one premium plane

    Thread Starter: Brandon SPEAKS

    So this is mostly hypothetical. If you were to have a plane collection build on decent user vintage planes but could buy one premium LN or LV what would it be? A no 4 because of the advantages of perfectly tuned smoother plane? A specialty like a shooting plane and tracks for a shooting...

    Last Post By: Jim Koepke Today, 9:31 PM Go to last post
    Rob Wolfbrandt

    need advice on track saw related purchases for building built-ins at home

    Thread Starter: Rob Wolfbrandt

    Hi Everyone, I've been reading this forum the past two days collecting as much information as I can about track saws, accessories, and the Festool MFT/3 table. There's so much knowledge and experience here that I thought it a good idea to request some opinions on what I'm thinking about doing. ...

    Last Post By: Rob Wolfbrandt Today, 8:56 PM Go to last post
  • Malcolm Schweizer

    There is no available content written by Malcolm Schweizer
  • Recent Polls

    Which Coping Sled is the Best (Votes: 44)

    1. Woodpeckers Coping Sled (Votes: 16)

    2. Infinity Professional Coping Sled (Votes: 16)

    3. Neither - Who needs a sled anyway? (Votes: 10)

    4. Both - Why buy only one when you can have two at twice the price? (Votes: 2)

  • Recent Forum Posts

    Bert Kemp

    corel problem smRT fill

    I'll try it again Kev, I did the idea Tony gave me and that worked , but I'll load the orginal again remove nodes Like Tony said, I'll take out those

    Bert Kemp Today, 11:23 PM Go to last post
    Bert Kemp

    Problem engraving.

    It really would help if we knew which machine , size. power and model

    Bert Kemp Today, 11:20 PM Go to last post
    Kevin Jenness

    Marking on dark wood?

    For a fine visible line, apply tape, slice the line with a knife and remove the tape on the waste side. I use this all the time for scribeing.

    Kevin Jenness Today, 11:17 PM Go to last post
    Bert Kemp

    Glowforge release

    Im sorry Bill where was it that he said that? I went back looking couldn't find that post. What number was it ?

    Bert Kemp Today, 11:17 PM Go to last post
    Fred Belknap

    Dent and Scratch (Powermatic) lathe purchase question

    My PM3520B will be five years old nest month and the only thing I have replaced under warranty is the power switch. The switch is $75.00 if you have

    Fred Belknap Today, 11:13 PM Go to last post
  • Recent Blog Posts