• Recent Articles

  • Recent Article Comments Widget

  • Hottest Threads

    Bennie Dempsey

    3D Planning Software

    Thread Starter: Bennie Dempsey

    Hey all! I would like to start planning out my projects before I begin them, as I've heard that's a good habit to have. I can find a modeling program online pretty easily, but I wanted to see what you guys use. I am awful at hand drafting so paper and pencil isn't my go-to for personal projects....

    Last Post By: Randy Heinemann Today, 1:47 PM Go to last post
    Paul F Franklin

    New Lee Valley Web Site

    Thread Starter: Paul F Franklin

    Seems the roll out of the new site is not going completely smoothly. Have been trying to place an order all morning and the site just spins when I try to checkout. Tried a few different browsers too. Guess I may have to call :eek: New site design seems nice and clean though but it will take...

    Last Post By: Paul F Franklin Today, 12:33 PM Go to last post
    Alan Lightstone

    High CRI Workshop LEDs

    Thread Starter: Alan Lightstone

    I've been spending tons of time looking for high CRI (>90, hopefully 93-95) LED bulbs / fixtures for my workshop build. I'm having a real tough time finding LED tube fixtures with high CRIs (looking for 4000-4100K fixtures). I can find Edison base bulbs or floods with high CRIs, but linear...

    Last Post By: Jay Champagne Yesterday, 8:36 PM Go to last post
    Ronald Blue

    Two Year Old Camaster Stinger III

    Thread Starter: Ronald Blue

    I have a locally available Camaster Stinger III. It's a 4 X 8 machine with a three head setup. Whats the benefit of the three head arrangement? Is it an alternative to an ATC system? What's a fair price? He says it was $18,000 new. He's discounted it a lot from that amount. Nearly half. He did say...

    Last Post By: Keith Outten Today, 9:52 AM Go to last post
    Tom Trees

    Suitable relay for three wire control on a VFD

    Thread Starter: Tom Trees

    Hello folks I have been walking through the steps with another forum member on setting up a VFD for his saw. Unfortunately the VFD does not have a relay OR COMMON for three wire control/push button station. Can any of you guys point me in the right direction to find a suitable relay for him? ...

    Last Post By: Tom Trees Today, 6:26 AM Go to last post
    Derek Cohen

    How to do these drawers?

    Thread Starter: Derek Cohen

    I am planning another build as a wedding gift, this time a niece. She picked out this entry hall table, which she wants in Jarrah. Straightforward enough build, with the case in mitred through dovetails the only tricky bit. I've done a few of these now, so know what lies in store. ...

    Last Post By: William Fretwell Today, 4:44 PM Go to last post
  • Robert Hazelwood

    There is no available content written by Robert Hazelwood
  • Recent Polls

  • Recent Forum Posts

    Mike Hutchison

    Stanley No. 45 Parts

    Jim K.
    Thanks for the detailed information. Maybe I should have
    included more information. To Wit: The long rods that came
    with my

    Mike Hutchison Today, 7:22 PM Go to last post
    johnny means

    Ambrosia is my new favorite color

    I actually call them glitches. Their our way of dealing with nasty inclusions and checking that are present in these highly disfigured

    johnny means Today, 7:01 PM Go to last post
    Derek Meyer

    Getting photos off old hard drive

    I use this device at work. It has two slots that can take either 2.5" or 3.5" SATA drives, and has USB ports and memory card readers built

    Derek Meyer Today, 6:41 PM Go to last post
    Barry McFadden

    Getting photos off old hard drive

    Sorry Steven.... but why over complicate things? The OP says he is not computer savy and you want him to try that?... all he needs to do is get a SATA

    Barry McFadden Today, 6:15 PM Go to last post
    Phil Mueller

    Jewelry boxes

    Carl, thanks for the post, they look fantastic. The wood combinations are great. Truly heirloom pieces the ladies in your life will enjoy.

    Phil Mueller Today, 5:57 PM Go to last post
  • Recent Blog Posts