Sawmill Creek Woodworking Community

Sections
Sawmill Creek News

Workshops

Woodturning

Social Woodworking

Tools

Lathes and Accessories

Table Saws and Accessories

Jigs and Fixtures

Cabinetry
Recent Articles
Recent Article Comments Widget
Hottest Threads

How to bend wood like this - Outdoor furniture project
Thread Starter: Alan Lightstone
Looking for a new project to do. I've been spending a few months upgrading the workshop / fixing minor annoyances, and really need to actually build something. I ran across this in a magazine ad. The furniture is supposedly solid teak, though I don't think that will be in the cards for...
Last Post By: Mike King Today, 3:50 PM

landscaping is my other hobby, record for me, 25 yards of mulch
Thread Starter: Brian Runau
My landscape guys clean up the beds and install mulch for me now, too old, but I planted everything you see except the very large mature trees. Shade garden, cutting garden, front. Thanks Brian
Last Post By: Brian Runau Today, 1:07 PM

SCM T130 bearing change
Thread Starter: Tom Yaegle
Has any one here done one? Looking for suggestions, thanks.
Last Post By: Jerry Bruette Today, 1:23 PM

LLAMBRICH Intergrated arbor and chuck
Thread Starter: Patty Hann
Opinions, please on integrated arbor and chuck for a DP. Am looking at the LLAMBRICH Keyless chucks ... integrated 2MT shank/arbor 1/32" to 3/8" (part# JK10-MT2) 1/32" to 1/2" (JK13-MT2) Thanks
Last Post By: Patty Hann Today, 1:45 PM

Lumber supply
Thread Starter: steven c newman
Has been restocked.. Bought 10 planks...for $30...had to cut a few of the 10 footers down, to fit into the Trunk of my Chevy Equinox... Eight 1 x 6 x 6' Five 1 x 4 x 6' And he threw in a stack of shorts And a 3/4" x 8" x 39" slab..
Last Post By: Mike Manning Today, 4:38 PM

Trying to Find Part for my Tripod
Thread Starter: Jim Koepke
I have a Gitzo tripod that was bought in the late 1970s. The rubber ring for tightening the nut on the telescoping section to raise and lower the camera has finally stretched to the point of uselessness. Years ago when talking to a rep. at Gitzo I was told the part is unavailable and my model...
Last Post By: George Yetka Today, 4:49 PM

David Stratton

There is no available content written by David Stratton

Recent Polls
Would you borrow a tool from someone? (Votes: 71)

Sure - why not? (Votes: 9)

Never. If I needed something, I'd buy or rent it. (Votes: 10)

Maybe. Depends on the person and the tool. (Votes: 52)
Recent Forum Posts

blade insert for delta/rockwell 12/14

I designed an aluminum insert for my Craftsman saw. A machinist friend milled it for me. The only time I have to hold it down is when I am cutting up
Lee Schierer Today, 5:18 PM

Swiss Army ... tool

For many years we had a tradition of cutting dow the family Christmas tree with the saw that some Swiss Army knives have. My favorite Victorinox had one
Maurice Mcmurry Today, 5:08 PM

Glue Chairs

I disassemble as much as possible, clean out the joints and tenons. For reassembly I make some long shavings out of oak. I apply glue to the tenon
Lee Schierer Today, 5:07 PM

Swiss Army ... tool

Modern folks only need to open Amazon packages, and they use a key.
Cameron Wood Today, 4:53 PM

Trying to Find Part for my Tripod

Jim At some point they switched to the tabs instead of the rubber.

Its amazing how well these are built. I would order the
George Yetka Today, 4:49 PM
Recent Blog Posts

Sections

Recent Articles

Recent Article Comments Widget

Hottest Threads

David Stratton

Recent Polls

Recent Forum Posts

Recent Blog Posts