1. Announcement:
    Picture Viewing Privileges
    Keith Outten (Administrator)
    05-02-2019
    Views:
    287,049
  2. Announcement:
    Thou Shalt Be Friendly Here
    Keith Outten (Administrator)
    01-07-2019
    Views:
    271,051
  3. Announcement:
    FreeStuff Winner List
    Keith Outten (Administrator)
    08-17-2013
    Views:
    261,524
  4. Announcement:
    Read Me First
    Keith Outten (Administrator)
    09-10-2008
    Views:
    463,669
Page 1 of 17 1234511 ... LastLast
Threads 1 to 25 of 406

Forum: Shop Made Tools and Machines

Share your Custom Tools, Machines, Jigs and Fixtures.

  1. Finding center of board

    Started by Aaron Inami, 08-04-2022 10:28 PM
    • Replies: 3
    • Views: 5,805
    10-06-2022, 5:44 PM Go to last post
  2. Question about tang slot

    Started by Adam Beaudoin, 01-30-2019 5:07 PM
    • Replies: 2
    • Views: 8,667
    07-10-2019, 6:34 AM Go to last post
  3. bearings on threaded shaft

    Started by al ladd, 05-17-2019 10:04 AM
    • Replies: 11
    • Views: 18,097
    06-05-2019, 12:28 PM Go to last post
  4. OtherT Track Options

    Started by Allen (AJ) Breese, 01-17-2015 9:33 AM
    • Replies: 14
    • Views: 15,947
    03-31-2015, 1:11 AM Go to last post
  5. New Tablesaw Fence Rails?

    Started by Andrew More, 02-26-2019 10:28 AM
    3 Pages
    1 2 3
    • Replies: 32
    • Views: 24,402
    06-06-2019, 4:29 PM Go to last post
  6. DIY Over Arm Dust collector

    Started by Andrew More, 02-10-2020 6:51 PM
    • Replies: 8
    • Views: 6,351
    03-02-2020, 12:50 PM Go to last post
    • Replies: 3
    • Views: 5,710
    03-17-2022, 10:33 PM Go to last post
  7. Shop Made Drum Sander plans

    Started by Ben Darrah, 09-25-2020 9:45 PM
    • Replies: 3
    • Views: 6,070
    09-29-2020, 5:42 PM Go to last post
  8. Striatech DVR Motor

    Started by Ben Darrah, 07-09-2023 1:55 PM
    • Replies: 1
    • Views: 6,490
    07-10-2023, 8:58 PM Go to last post
  9. pipe clamp vise

    Started by Ben Kann, 10-22-2017 12:27 PM
    • Replies: 3
    • Views: 9,206
    10-23-2017, 12:33 PM Go to last post
  10. Wooden Pulleys

    Started by Benjamin Hall, 04-09-2015 7:50 PM
    • Replies: 6
    • Views: 11,158
    06-09-2015, 9:38 AM Go to last post
    • Replies: 0
    • Views: 8,973
    02-28-2015, 4:37 PM Go to last post
  11. How Does One Peen Steel Rod?

    Started by Bill Adamsen, 04-27-2015 10:00 AM
    • Replies: 14
    • Views: 17,114
    06-29-2015, 8:35 PM Go to last post
    • Replies: 11
    • Views: 10,078
    03-09-2017, 6:45 PM Go to last post
  12. Pneumatic Springs?

    Started by Bill Adamsen, 03-28-2017 12:00 PM
    • Replies: 14
    • Views: 12,611
    06-30-2017, 2:08 PM Go to last post
  13. Bandsaw Feed Assist

    Started by Bill Adamsen, 06-27-2017 7:58 AM
    • Replies: 11
    • Views: 13,916
    07-03-2017, 11:20 AM Go to last post
  14. Turn an old table saw into ??????

    Started by Bill Carey, 01-13-2018 1:27 PM
    2 Pages
    1 2
    • Replies: 21
    • Views: 21,866
    07-08-2018, 9:49 AM Go to last post
  15. moxon overbuild??

    Started by Bill Carey, 01-08-2019 10:20 PM
    2 Pages
    1 2
    • Replies: 15
    • Views: 14,861
    03-17-2019, 10:28 PM Go to last post
  16. Moxon v2.2

    Started by Bill Carey, 03-01-2020 2:04 PM
    • Replies: 5
    • Views: 9,303
    08-26-2020, 1:19 AM Go to last post
  17. Marking gauge prototype

    Started by Bill Carey, 02-28-2021 6:49 PM
    • Replies: 9
    • Views: 10,351
    06-01-2021, 2:59 PM Go to last post
  18. is there a cure for pattern-itis?

    Started by Bill Carey, 04-11-2021 11:39 AM
    • Replies: 3
    • Views: 8,680
    04-11-2021, 4:38 PM Go to last post
    • Replies: 0
    • Views: 3,358
    07-28-2022, 1:22 AM Go to last post
  19. Expansion arbor

    Started by Bill Jobe, 04-26-2016 3:21 PM
    • Replies: 2
    • Views: 8,674
    05-01-2016, 4:29 AM Go to last post
  20. Mounting Drumsander

    Started by Bill Sutherland, 02-25-2017 10:40 PM
    • Replies: 6
    • Views: 10,931
    04-29-2018, 4:29 PM Go to last post

Forum Information and Options

Users Browsing this Forum

There are currently 4 users browsing this forum. (0 members & 4 guests)

Thread Display Options

Use this control to limit the display of threads to those newer than the specified time frame.

Allows you to choose the data by which the thread list will be sorted.

Order threads in...

Note: when sorting by date, 'descending order' will show the newest results first.

Icon Legend

Contains unread posts
Contains unread posts
Contains no unread posts
Contains no unread posts
More than 30 replies or 250 views
Hot thread with unread posts
More than 30 replies or 250 views
Hot thread with no unread posts
Closed Thread
Thread is closed
Thread Contains a Message Written By You
You have posted in this thread

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •