• Recent Articles

  • Hottest Threads

    Dave Anderson NH

    Time for some levity

    Thread Starter: Dave Anderson NH

    With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.

    Last Post By: Mike Henderson Today, 6:04 PM Go to last post
    Rick Potter

    Gassed up today

    Thread Starter: Rick Potter

    While we were on a trip last week a war started and gas prices went crazy everywhere. Got back Monday night. Today, Friday, we decided to gas up two cars. The cheapest gas we saw while driving around was $5.47 for reg unleaded at an Arco station. That was cash, credit was $5.67. We pulled into...

    Last Post By: Curt Harms Today, 9:48 AM Go to last post
    Robert Hartmann

    Garage cost...are you kidding me?

    Thread Starter: Robert Hartmann

    I retired from the Air Force close to two years ago. It took us until now to find the house we wanted. So, I was ready to finally have a space dedicated for a wood shop instead of cramming into here or there as we moved every three years. We have a great house with some land and a perfect spot...

    Last Post By: Jim Becker Yesterday, 8:43 PM Go to last post
    Dale Osowski

    Krenov Style Apron Plane

    Thread Starter: Dale Osowski

    Attention to my woodworking friends! I have a fair amount of Gaboon Ebony cutoffs I've collected over the years and I'm looking to put them to good use. I'm thinking about making a number of small Krenov style apron / block planes that would be available for sale. They would be made of Gaboon...

    Last Post By: Dale Osowski Today, 10:35 AM Go to last post
    Gregory King

    New Mig

    Thread Starter: Gregory King

    Thinking about buying my first welder. Probably going a bit overboard on size, but looking at the Miller 212 Autoset. A good welder or not? I like the Miller line and if I decide down the road to sell it, it should command a decent return. Or I hope it should.

    Last Post By: Bill George Today, 7:42 PM Go to last post
    Bruce Jones

    Tear Drop WIP

    Thread Starter: Bruce Jones

    Okay everyone the progress continues on my new WIP. Made from staves then turned on the lathe. I'm just about done carving out the first side. You can see in the photos some of the hand tools being used to carve the tear drops to a point. The first step is to make ta hole using a Dremel and a...

    Last Post By: Bruce Jones Today, 2:22 PM Go to last post
  • Recent Forum Posts

    Maurice Mcmurry

    Air Conditioner Maintenance

    I am still learning that the fins are very delicate, not much thicker than aluminum foil. A little carelessness has led to a lot of time spent with the

    Maurice Mcmurry Today, 8:12 PM Go to last post
    Neil Strong

    3/4" D-Way bowl gouge

    Reed

    Thank you for your post.

    What I'm seeking is input on Dave's 3/4" BG, which only comes with the 'U' fluted profile.

    Neil Strong Today, 7:55 PM Go to last post
    Bill George

    New Mig

    I just order off Amazon they have the name brand ones and you do not need to drive all over town. Home Depot carries a lot also, zero difference between

    Bill George Today, 7:42 PM Go to last post
    Dave Garrett

    Residential laser exhaust vent pipe design

    I cut tons of latex and have yet to find anything as disgusting and likely to make new enemies. I vent out the window in the dead of night and slide out

    Dave Garrett Today, 7:39 PM Go to last post
    Clifford McGuire

    Sharpening Station

    I have a pretty simple setup. It sits on an old portable typewriter table from the 1960's

    Worksharp 3000 is used to hone and occasionally

    Clifford McGuire Today, 7:32 PM Go to last post