• Recent Articles

  • Hottest Threads

    Dave Anderson NH

    Time for some levity

    Thread Starter: Dave Anderson NH

    With all of the negativity and political stuff going on with the Covid-19 virus it is time to look at the humorous side of things. Feel free to add more, but keep it clean or it will be deleted.

    Last Post By: Mike Henderson Today, 6:04 PM Go to last post
    Rick Potter

    Gassed up today

    Thread Starter: Rick Potter

    While we were on a trip last week a war started and gas prices went crazy everywhere. Got back Monday night. Today, Friday, we decided to gas up two cars. The cheapest gas we saw while driving around was $5.47 for reg unleaded at an Arco station. That was cash, credit was $5.67. We pulled into...

    Last Post By: Curt Harms Today, 9:48 AM Go to last post
    Dale Osowski

    Krenov Style Apron Plane

    Thread Starter: Dale Osowski

    Attention to my woodworking friends! I have a fair amount of Gaboon Ebony cutoffs I've collected over the years and I'm looking to put them to good use. I'm thinking about making a number of small Krenov style apron / block planes that would be available for sale. They would be made of Gaboon...

    Last Post By: Dale Osowski Today, 10:35 AM Go to last post
    Gregory King

    New Mig

    Thread Starter: Gregory King

    Thinking about buying my first welder. Probably going a bit overboard on size, but looking at the Miller 212 Autoset. A good welder or not? I like the Miller line and if I decide down the road to sell it, it should command a decent return. Or I hope it should.

    Last Post By: Bill George Today, 7:42 PM Go to last post
    Bruce Jones

    Tear Drop WIP

    Thread Starter: Bruce Jones

    Okay everyone the progress continues on my new WIP. Made from staves then turned on the lathe. I'm just about done carving out the first side. You can see in the photos some of the hand tools being used to carve the tear drops to a point. The first step is to make ta hole using a Dremel and a...

    Last Post By: Bruce Jones Today, 2:22 PM Go to last post
    Randall J Cox

    what kind of clear plastic to use in kitchen

    Thread Starter: Randall J Cox

    We have an island in the kitchen and the top is made of beautiful, thick walnut. Its so nice, we don't want to use it, nor did the previous owners for 15 years. I was going to make a cutting board to place on top of it of either walnut, ash, white oak or oak to be able to use it. The wifey does...

    Last Post By: Randall J Cox Today, 3:24 PM Go to last post
  • Recent Forum Posts

    Joe A Faulkner

    Hybrid Workshop Size?

    I have A 22x22 shop building and most if not all the tools you list. Unisaw with a 52 fence, SCM station, router table flanked by two 4 counters, 18

    Joe A Faulkner Today, 10:14 PM Go to last post
    William Fretwell

    Sharpening Station

    Based on a granite off cut, edges polished, the granite adds good weight. Poplar legs from a tree I cut down. The drawer has a band aid dispenser along

    William Fretwell Today, 10:09 PM Go to last post
    Ronald Blue

    And POOF! It Was Gone!

    I agree Lawrence. That's partly why I started this thread. I never saw the posts that ran it aground so I don't know what transpired. Locking it yes but

    Ronald Blue Today, 10:00 PM Go to last post
    Dave Zellers

    And POOF! It Was Gone!

    Yes- I have a hunch that is why the thread was removed from public view and not just locked.

    Nothing is ever actually deleted.

    Dave Zellers Today, 9:47 PM Go to last post
    Frederick Skelly

    Need air compressor advice

    Thank you again folks. Today I saw a sweet little Makita MAC210Q (LINK), whose specs are very comparable to the CAT I was inquiring about. I really like

    Frederick Skelly Today, 9:34 PM Go to last post