Sawmill Creek Woodworking Community - Powered by vBulletin
  • Register
  • Help
  • What's New?
  • Forum
  • Articles
    • The Sawmill Creek Press
  • Blogs
  • Donate
  • Sponsors
  • Friends of the Creek
  • Advanced Search
  • Home
  • Home
  • Workshops

  1. If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.

  • Sections

    • Sawmill Creek News
    • Workshops
    • Woodturning
    • Social Woodworking
    • Tools
      • Lathes and Accessories
      • Table Saws and Accessories
    • Jigs and Fixtures
    • Cabinetry

  • Recent Articles

  • Hottest Threads

    Bill Dufour

    Best Hitchcock movie introduction

    Thread Starter: Bill Dufour

    We have a friend about 45 years old. She has never seen a Alfred Hitchcock movie in her life. She likes modern shoot um ups and super hero movies. It has to be in color. What would be the best movie to introduce Hitchcock to her. The Birds, Psycho, or what. Bill D

    Last Post By: Patty Hann Yesterday, 8:56 PM Go to last post
    David Bryan West

    Help with new to me tecnomax scm fs41 elite planer jointer table alignment

    Thread Starter: David Bryan West

    I have just finished getting this machine ready to use, cleaned up a bit and modified my dust hose hookups etc, only to find my tables don’t seem to be co planar. I just sold my beloved from day one, dj20 that was dialed in so nicely recently and I need this to be setup the same way. I just...

    Last Post By: Erik Loza Yesterday, 12:28 PM Go to last post
    Tom Bender

    Winter soon

    Thread Starter: Tom Bender

    Good time to tune up the weatherstripping and the snowblower. Try out the furnace too.

    Last Post By: Patty Hann Today, 5:11 AM Go to last post
    Jimmy Harris

    On the Feedback of Sharpening Stones

    Thread Starter: Jimmy Harris

    So I know a lot of people love their sharpening jigs and claim it's the only way to get consistent and repeatable angles on their blades. Which, being someone who's freehand sharpened their whole life, always struck me as kind of odd. I get it if you don't do much sharpening or are new the realm...

    Last Post By: Russell Nugent Yesterday, 11:54 PM Go to last post
    Charlie Velasquez

    Electrical code and others… public access

    Thread Starter: Charlie Velasquez

    Recent court case https://www.republicreport.org/2023/federal-appeals-couraffirms-the-right-to-publish-the-law/ One issue I have had in the past is having an electrical project that requires a city permit and must adhere to the city code and not being able to easily find the code. In both my...

    Last Post By: Bill Howatt Yesterday, 12:52 PM Go to last post
    Doug Walls

    Nova Viking Floor Model Version

    Thread Starter: Doug Walls

    I'm looking at getting a Nova Viking for my garage mainly for woodworking use. I'm probably going to go with the floor model version because of the extra height adjustability, but the base seems kind of narrow for a floor model drill press! Has anyone had any problems with the Viking floor...

    Last Post By: Doug Walls Yesterday, 1:05 PM Go to last post

  • Workshops RSS Feed

    Lighting the Small Workshop - by Jack Lindsey 

    by
    Jack Lindsey
    • View Profile
    • View Forum Posts
    • View Blog Entries
    • View Articles
        Number of Views: 218843 
    Article Preview

    Lighting the Small Workshop
    By Jack Lindsey

    "Ten years have passed since I wrote the Fine Woodworking article on lighting the small shop," Jack Lindsey explains, but much has changed. Jack comprehensively explores lighting a hobbyist or small industrial shop, drawing on over 25 years of professional lighting experience, covering topics such as fixture and ballast selection, lamp life, and color when employing fluorescent lamps.
     ...
    Read More Read More 89 Comments

  • Recent Forum Posts

    Clint Baxter

    which Whitehill T&G profile do I need?

    Your panel will be loose in the groove using those, especially with the 66.

    Clint

    Clint Baxter Today, 7:11 AM Go to last post
    Clint Baxter

    Bolts for T-Slot on cast iron tops - what size?

    Lit’s of options out there for T-slot nuts. Here is one from Infinity tools, https://www.infinitytools.com/t-slot...yABEgLs5_D_BwE

    Clint Baxter Today, 6:52 AM Go to last post
    Patty Hann

    Winter soon

    "Winter is coming."

    Patty Hann Today, 5:11 AM Go to last post
    Greg Quenneville

    Slider question

    I will echo the advice to upsize the slider to 10’ if you can. I have two Felder combos…one with the short slider and one with the 78”. The smaller machine

    Greg Quenneville Today, 5:02 AM Go to last post
    Amr Hadi

    Bearings and shims on a Delta 46-230

    Hello folks, I've had this Delta lathe for a couple of years, bought it from a cabinetmaker who was retiring. Recently I decided I want to graduate from

    Amr Hadi Today, 3:41 AM Go to last post
  • Sawmill Creek
  • Archive
  • Terms of Service
  • Top
All times are GMT -4. The time now is 7:18 AM.
Powered by vBulletin® Version 4.2.5
Copyright © 2023 vBulletin Solutions Inc. All rights reserved.